Before using this unit, carefully read the sections entitled “USING THE UNIT SAFELY” and “IMPORTANT NOTES”
on back side. These sections provide important information concerning the proper operation of the unit.
Additionally, in order to feel assured that you have gained a good grasp of every feature of your new unit, read
Owner's Manual in its entirety. This manual should be saved and kept on hand as a convenient reference.
Owner’s Manual
RS-232 Connector (RS-232 Conversion Cable) Specifications
D-sub 9-pin (female)
5 4 3 2 1
9 8 7 6
TXD
RXD
GND
3.5mm miniature
phone plug
5 4 3 2 1
9 8 7 6
TXD
RXD
GND
Pin No.
Signal
1
N.C.
2
RXD
3
TXD
4
N.C.
5
GND
6
N.C.
7
N.C.
8
N.C.
9
N.C.
Communication method
Synchronous (asynchronous), full-duplex
Communication speed
9600 bps, 19200 bps, 38400 bps, 115200 bps
Parity
none
Data length
8 bit
Stop bit
1 bit
Code set
ASCII
Flow control
none
Cable Wiring Diagram
When using the included RS-232 conversion cable, RXD, TXD, and GND are wired as shown below.
Unit end
(conversion cable end)
Controller end
N.C. : 1
1 :
RXD : 2
2 : RXD
TXD : 3
3 : TXD
N.C. : 4
4 :
GND : 5
5 : GND
N.C. : 6
6 :
N.C. : 7
7 :
N.C. : 8
8 :
N.C. : 9
9 :
* When you want to extend the RS-232 conversion cable, use a straight cable.
Attaching the Ferrite Cores
1.
Open an included ferrite core by spreading apart the tabs at two places.
2.
Attach the ferrite core to an HDMI cable, LAN cable, or RS-232 conversion cable.
* Close the ferrite core by pressing down on each tab until it clicks into place.
Attach near the base of the plug at
the end that connects to the unit.
Connection Examples
* For a connection to the HDBaseT connector, use a Cat5e (Category 5e) or higher shielded LAN cable.
* *For a connection to the RS-232 connector, use the included RS-232 conversion cable.
HDMI INPUT
connector
RS-232
connector
RS-232-compatible
projector, etc.
RS-232-compatible
device (computer, etc.)
Displays,
projectors, etc.
Roland XS series device, etc.
HT-RX01
HDBaseT OUTPUT
connector
RS-232
connector
RS-232
connector
RS-232
connector
RS-232-compatible
device (computer, etc.)
Displays,
projectors, etc.
Roland V-40HD device, etc.
HT-RX01
HT-TX01
RS-232
connector
HDMI INPUT
connector
HDMI OUTPUT
connector
Panel Descriptions
HT-TX01 (Transmitter)
1 2
3
* These connectors are not used.
4
5
6
HT-RX01 (Receiver)
1 2
7
* These connectors are not used.
4
8
6
No.
Name
Explanation
1
Power indicator
This lights up when power is supplied.
2
LINK indicator
This lights up when the transmitter/receiver is correctly connected
3
HDMI INPUT connector
The HDMI signal from the source device is input here.
4
AC adaptor connector
This is for connecting the included AC adaptor.
No.
Name
Explanation
5
HDBaseT (TX) connector
This is for connecting a receiver.
6
RS-232 connector
This is for connecting a remote-control device (RS-232-compatible
computer, projector, or the like) using the included RS-232 conversion cable.
7
HDMI OUTPUT connector
This outputs the HDMI signal to a display device.
8
HDBaseT (RX) connector
This is for connecting a transmitter, Roland XS series unit, or other such
device.
Main Features
Checking the Included Items
• The unit
• AC adaptor, insertion plugs (3 types)
• RS-232 conversion cable (2 m)
• Ferrite core x 3
• Owner’s Manual (this document)
This unit is a transmitter/receiver for long-distance transmission of HDMI signals over up to 100 meters using a single LAN cable (Cat5e or higher).
• Support for 1080/59.94p (full HD) and 3D video
• Support for HDMI 1.4 and HDCP 2.0
• Support for RS-232 signals
Attaching an AC Adaptor Insertion Plug
1.
Attach an included AC adaptor insertion plug to the AC adaptor.
* Attach the insertion plug for your country or region.
* Attach the insertion plug by pressing it in until it clicks into place.
* Be sure always to use the included AC adaptor with the unit.
To detach, pull out the insertion plug
while squeezing the left and right
sides of the lock section inward.
Main Specifications
Roland HT-TX01/HT-RX01 : HDBaseT TRANSMITTER/HDBaseT RECEIVER
Dimensions
Copyright © 2014 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in
any form without the written permission of ROLAND CORPORATION.
90
93
81
69
24
24.9
60
73.4
Unit: mm
Input Formats
480/59.94i, 576/50i, 480/59.94p, 576/50p, 720/59.94p, 720/50p,
1080/59.94i, 1080/50i, 1080/59.94p, 1080/50p, 640 x 480, 800 x 600,
1024 x 768, 1280 x 768, 1280 x 1024, 1366 x 768, 1400 x 1050,
1600 x 1200, 1920 x 1200
* RGB formats : Conforms to VESA DMT Version 1.0 Revision 11.
* The maximum refresh rates of RGB is 75 Hz. (excluding 1600 x 1200
and 1920 x 1200. The refresh rate of these 2 is 60Hz)
* 1920 x 1200/60Hz : Reduced blanking
* Also check the supported resolutions of the connected device.
Audio Formats
The maximum is PCM 8ch, Dolby Digital, True HD DTS-HD Master Audio
Input Connectors
HT-TX01
HDMI x 1: Type A 19 pins
HT-RX01
RJ45 x 1
Output Connectors
HT-TX01
RJ45 x 1
HT-RX01
HDMI x 1: Type A 19 pins
Other Connectors
RS-232 x 1: 9 pins D-sub type * When using additional RS-232 cable.
Transmission distance
The maximum is 100 m (328 ft)
* The available distance depends on the quality of the LAN cable.
Operating temperature range
0 to 40 degree C
32 to 104 degrees F
Operating temperature humidity
10 to 85 % (no condensation)
Storage temperature range
-20 to 60 degree C
-4 to 140 degrees F
Storage temperature humidity
10 to 85 % (no condensation)
Power Supply
AC Adaptor
Power Consumption
10 W
Dimensions
81 (W) x 93 (D) x 24 (H) mm
3-3/16 (W) x 3-11/16 (D) x 1 (H) inches
Weight excl. AC adaptor
300 g
11 oz
* In the interest of product improvement, the specifications and/or appearance of this unit are subject to
change without prior notice.
When you need repair service, access this URL and find your nearest Roland Service Center or
authorized Roland distributor in your country.
https://roland.cm/service
Roland Service Centers and Distributors
Roland Service Centers and Distributors
When you need repair service, access this URL and find your nearest Roland Service Center or authorized Roland distributor in
your country.
https://roland.cm/service
Roland Service Centers and Distributors
Roland Service Centers and Distributors
When you need repair service, access this URL and find your nearest
Roland Service Center or authorized Roland distributor in your country.
https://roland.cm/service
Roland Service Centers and Distributors
Roland Service Centers and Distributors
*5100044591-04*
