49
Chapter 4 Introduction to Effects and Parameters
Chapter
4
SH (Sound Hold)
You can have sound played on the guitar be held
continuously. This effect allows you to perform the melody
in the upper registers while holding a note in the lower
registers.
* This function will not work properly when two or more notes
are played simultaneously.
SDD (Sub Delay)
This is a delay with the maximum delay time of 400 ms. This
effect is useful for making the sound fatter.
EQ (Equalizer)
Adjusts the tonal quality. A parametric type equalizer is used
for the upper and lower midrange.
Parameter/
Range
Explanation
Hold
Off, On
Switches the hold sound on and off.
Normally, this is assigned to the CTL pedal.
Rise Time
0–100
Adjusts how rapidly the Sound Hold sound
is produced.
Effect Level
0–120
Adjusts the volume of the hold sound.
Parameter/
Range
Explanation
Delay Time
0 ms–400 ms,
BPM
–BPM
Adjusts the delay time.
* When set to BPM, the value of each parameter will be set according to
the value of the Master BPM (p. 51) specified for each patch. This makes
it easier to achieve effect sound settings that match the tempo of the
song (synchronizing the time to twice or four times the time length of
the BPM when the set time is increased).
When setting to BPM, press PARAMETER [
] several times to
display the Master BPM settings screen.
Feedback
0–100
Adjusts the volume that is returned to the
input.
Feedback refers to returning the delayed signal back into the input
of the delay. Higher settings will result in more delay repeats.
Effect Level
0–120
Adjusts the volume of delay sound.
Parameter/
Range
Explanation
On/Off
Off, On
Turns the EQ on/off.
Low Cut (Low Cut Filter)
Flat, 55 Hz–800 Hz
This sets the frequency at which the low cut
filter begins to take effect.
This lets you cut the low-end component below the set frequency to
create a clear, distinct low end, thereby bringing out the high end of
the effect. When “Flat” is selected, the low cut filter will have no ef-
fect.
Low EQ
-20 dB–+20 dB
Adjusts the low frequency range tone.
Low-Middle Frequency
20.0 Hz–10.0 kHz
Specify the center of the frequency range
that will be adjusted by the “Lo-Middle
EQ.”
Low-Middle Q
0.5–16
Adjusts the width of the area affected by the
EQ centered at the “Lo-Middle frequency.”
Higher values will narrow the area.
Higher values will narrow the area.
Low-Middle EQ
-20 dB–+20 dB
Adjusts the low-middle frequency range
tone.
High-Middle Frequency
20.0 Hz–10.0 kHz
Specify the center of the frequency range
that will be adjusted by the “Hi-MidDle
EQ.”
High-Middle Q
0.5–16
Adjusts the width of the area affected by the
EQ centered at the “Hi-Middle frequency.”
Higher values will narrow the area.
Higher values will narrow the area.
High-Middle EQ
-20 dB–+20 dB
Adjusts the high-middle frequency range
tone.
High EQ
-20 dB–+20 dB
Adjusts the high frequency range tone.
High Cut (High Cut Filter)
700 Hz–11.0kHz, Flat
This sets the frequency at which the high cut
filter begins to take effect.
This allows you to get a mild effect sound by cutting the high-end
component above the set frequency. When “Flat” is selected, the
high cut filter will have no effect.
Level
-20 dB–+20 dB
Adjusts the volume before the equalizer.
GT-8_e.book 49 ページ ２００７年６月２９日 金曜日 午後３時５５分
