16
Using the SOLO Function
You can save and call up the panel settings (those enclosed by
the line in the figure) for sounds you create with the LEAD
channel. On this unit, this function is called “SOLO.”
By default, “Loud Metal” (p. 20) sample settings are saved in the
SOLO function.
*
The VOLUME setting for the LEAD channel is not saved.
*
The LOOPER settings and the recorded phrase are not saved.
1.
Create a sound with the LEAD channel.
2.
Set the SOLO volume at 0 (zero).
If the SOLO volume is set
high, the sound may be
unexpectedly loud when the
panel settings are saved.
Before saving, lower the
volume to 0.
3.
Press and hold the SOLO switch on the panel
until the indicator starts to flash
(approximately 2 seconds or longer).
When the panel settings are
saved, the indicator
changes to a steadily
lighted state.
*
Never switch off the power
while the indicator is flashing.
4.
Adjust the volume for the SOLO function.
*
Saved panel settings remain in memory even after the power is
turned off.
1.
While at the JC CLEAN or LEAD channel, press
the SOLO switch on the panel.
The SOLO indicator lights up and the panel settings stored
in memory are called up.
*
When no panel settings have been saved, or when you’re using the unit
for the first time, the product’s factory-default settings (“Loud Metal” (p.
20) sample settings) are called up.
1.
Press the SOLO switch on the panel to call up
the saved settings.
2.
Turn the panel knob for the item you want to
change, and modify the setting.
*
The SOLO indicator goes out briefly when the position of the
turned knob coincides with the position stored in memory.
3.
Pressing the SOLO switch on the panel until
the indicator starts to flash (approximately 2
seconds or longer) saves the changes to the
settings.
*
Never switch off the power while the indicator is flashing.
*
Once the new settings have been saved, the previous settings in
effect before the changes cannot be called up again.
*
To quit without saving the changes, press the SOLO switch or the
SELECT switch.
You can switch channels using the SELECT switch and the SOLO
switch.
*
When a momentary-type footswitch pedal is connected, it also
performs the same operation.
Saving the Panel Settings
Calling Up Panel Settings
Changing or Checking Saved Panel
Settings
Switching the SOLO Function and the
LEAD and JC CLEAN Channels
SELECT
switch
SOLO
switch
SOLO switch
SELECT switch
Returning to the Factory-default Settings
Hold down the TAP switch and the SOLO switch at the same
time and switch on the power.
The SOLO indicator flashes and the settings saved with the
SOLO function are returned to their factory defaults.
cube-80x.book 16 ページ ２００８年１２月１２日 金曜日 午後６時７分
Summary of Contents for CUBE-80X
