MFX/IFX Parameters
41
03 ISOLATOR
This is an equalizer which cuts the volume greatly, allowing you to
add a special effect to the sound by cutting the volume in varying
ranges.
L in
L out
R out
R in
Isolator
Isolator
Low Boost
Low Boost
Isolator
Isolator
Low Boost
Low Boost
Parameter
Value
Explanation
Low Level
(Boost/Cut Low)
-60–+4 [dB]
These boost and cut each of the High,
Middle, and Low frequency ranges.
At -60 dB, the sound becomes inaudible.
0 dB is equivalent to the input level of
the sound.
Mid Level
(Boost/Cut Mid)
-60–+4 [dB]
High Level
(Boost/Cut High)
-60–+4 [dB]
Low AP Sw
(Anti
Phase Low Switch)
OFF, ON
Turns the Anti-Phase function on and off
for the Low frequency ranges.
When turned on, the counter-channel of
stereo sound is inverted and added to
the signal.
Low AP Level
(Anti Phase Low Level)
0–127
Adjusts the level settings for the Low
frequency ranges.
Adjusting this level for certain
frequencies allows you to lend emphasis
to specific parts (This is effective only for
stereo source.).
Mid AP Sw
(Anti
Phase Mid Switch)
OFF, ON
Settings of the Anti-Phase function for
the Middle frequency ranges.
The parameters are the same as for the
Low frequency ranges.
Mid AP Level
(Anti Phase Mid Level)
0–127
Boost Sw
(Low Boost Switch)
OFF, ON
Turns Low Booster on/off.
This emphasizes the bottom to create a
heavy bass sound.
Boost Level
(Low Boost Level)
0–127
Increasing this value gives you a heavier
low end.
Depending on the Isolator and filter
settings this effect may be hard to
distinguish.
Level
0–127
Output Level
04 LOW BOOST
Boosts the volume of the lower range, creating powerful lows.
L in
L out
R out
R in
Low Boost
Low Boost
2-Band EQ
2-Band EQ
Low Boost
Low Boost
2-Band EQ
2-Band EQ
Parameter
Value
Explanation
Boost Freq
(Boost Frequency)
50, 56, 63, 71, 80,
90, 100, 112, 125
[Hz]
Center frequency at which the lower
range will be boosted
Boost Gain
0–+12 [dB]
Center frequency at which the lower
range will be boosted
Boost Wid
(Boost Width)
WIDE, MID,
NARROW
Width of the lower range that will be
boosted
Low Gain
-15–+15 [dB]
Amount of boost/cut for the low-
frequency range
High Gain
-15–+15 [dB]
Amount of boost/cut for the high-
frequency range
Level
0–127
Output Level
05 SUPER FILTER
This is a filter with an extremely sharp slope. The cutoff frequency
can be varied cyclically.
L in
L out
R out
R in
Super Filter
Super Filter
Super Filter
Super Filter
Parameter
Value
Explanation
Filt Type
(Filter Type)
LPF, BPF, HPF,
NOTCH
Filter type
Frequency range that will pass through
each filter
LPF:
Frequencies below the cutoff
BPF:
Frequencies in the region of the
cutoff
HPF:
Frequencies above the cutoff
NOTCH:
Frequencies other than the
region of the cutoff
Filt Slope
(Filter Slope)
-12, -24, -36 [dB]
Amount of attenuation per octave
-12 dB:
Gentle,
-24 dB:
Steep,
-36 dB:
Extremely steep
Filt Cutoff
(Filter Cutoff)
0–127
Cutoff frequency of the filter
Increasing this value will raise the cutoff
frequency.
Filt Reso
(Filter Resonance)
0–100
Filter resonance level
Increasing this value will emphasize the
region near the cutoff frequency.
Filt Gain
(Filter Gain)
0–+12 [dB]
Amount of boost for the filter output
Mod Switch
(Modulation Switch)
OFF, ON
On/off switch for cyclic change
Mod Wave
(Modulation Wave)
TRI, SQR, SIN,
SAW1, SAW2
How the cutoff frequency will be
modulated
TRI
: Triangle wave
SQR
: Square wave
SIN:
Sine wave
SAW1:
Sawtooth wave (upward)
SAW2:
Sawtooth wave (downward)
SAW1
SAW2
Rate Sync
(Rate (sync switch))
OFF, ON
If this is ON, the rate synchronizes with
the tempo of the rhythm.
&
Rate Hz
(Rate (Hz))
0.05–10.00 [Hz]
Frequency of modulation
Rate Note
(Rate (note))
Note
&
Depth
0–127
Depth of modulation
Attack
0–127
Speed at which the cutoff frequency will
change This is effective if Modulation
Wave is SQR, SAW1, or SAW2.
Level
0–127
Output Level
