Roland AX-EDGE, Parameter Manual, Page: 34 / 72

SYSTEM EFFECT Parameters
34
Reverb Parameters
NOTE
The SYSTEM EFFECT reverb cannot be edited if the currently selected
program’s REVERB Src is set to “PRG” (the settings are specified by the
program sound parameters). You can either edit the reverb settings for the
program, or change Src to “SYS” and edit them.
INTEGRA
Parameter Value Explanation
Type
01:
ROOM1
02:
ROOM2
03: HALL1
04: HALL2
05: PLATE
Selects the types of reverb.
OFF:
Reverb is not used
Room 1/2: Room
Hall 1/2: Hall
Plate: Plate
Pre Delay
0–100 [msec]
Adjusts the delay time from the direct
sound until the reverb sound is heard.
Time 0.1–10.0 [sec] Time length of reverberation
Density 0–127 Density of reverb
Diffusion 0–127
Adjusts the change in the density of the
reverb over time.
The higher the value, the more the
density increases with time.
(The effect of this setting is most
pronounced with long reverb times.)
LF Damp
0–100
Adjusts the low-frequency portion of the
reverb.
HF Damp 0–100
Adjusts the high-frequency portion of
the reverb.
Spread 0–127 Reverb spread
Tone
0–127 Tonal character of the reverb
WARM HALL
Parameter Value Explanation
Pre Delay 0–100 [msec]
Adjusts the delay time from the direct
sound until the reverb sound is heard.
Time 0.3–30 [sec] Time length of reverberation
PreLPF
16–15000 [Hz],
Bypass
Frequency above which to cut the high-
frequency portion of the sound entering
the reverb
PreHPF
16–15000 [Hz],
Bypass
Frequency below which to cut the low-
frequency portion of the sound entering
the reverb
PreLoop LPF
16–15000 [Hz],
Bypass
Frequency above which to cut the
high-frequency portion of the extended
reverberation
Diffusion 0–127
Adjusts the change in the density of the
reverb over time.
HF Damp Freq 1000–8000 [Hz]
Frequency above which to cut the high-
frequency portion of the reverb
HF Damp Ratio 0.1–1.0
Amount by which to attenuate the high-
frequency portion of the reverb
HALL
Parameter Value Explanation
Pre Delay
0.0–100 [msec]
Adjusts the delay time from the direct
sound until the reverb sound is heard.
Time 0–127 Time length of reverberation
Size 1–8 Size of room/hall
High Cut
160–12500 [Hz],
BYPASS
Frequency above which the high-
frequency portion of the final output
sound is cut (BYPASS: no cut)
Density 0–127 Density of reverb
Diffusion 0–127
Adjusts how reverb density increases over
time. (This effect is especially noticeable
with long reverb times.)
LF Damp F 50–4000 [Hz]
Frequency below which the low-
frequency portion of the reverb sound
is cut.
Parameter Value Explanation
LF Damp G -36–0 [dB]
LF damp attenuation amount (0: no
effect)
HF DampF 4000–12500 [Hz]
Frequency above which the high-
frequency portion of the reverb sound
is cut
HF Damp G -36–0 [dB]
HF damp attenuation amount (0: no
effect)
GS
Parameter Value Explanation
Char
ROOM1–3,
HALL1–2, PLATE,
DELAY, PAN-DELAY
Type of reverb
Pre LPF 0–7
Amount of high-frequency attenuation
for the sound being input to the reverb
Level 0–127 Time length of reverberation
Feedback 0–127
Level at which the reverb sound is
returned to the input
SRV2000
Parameter Value Explanation
Selection
Selects the type of reverb offered by the Roland SRV-2000
digital reverb.
R37–R0.3
Room reverb. Higher values increase the
size of the room.
H37–H15
Hall reverb. Higher values increase the
size of the concert hall.
P-B
Plate reverb. A more flamboyant reverb
sound than P-A.
P-A Plate reverb
Pre Delay 0–160
Adjusts the delay time from the direct
sound until the reverb sound is heard.
Time 1–990 [msec] Time length of reverberation
HF Damp 0.05–1.00
Adjusts the high-frequency portion of
the reverb.
Density 0–9
Adjusts the density of the late
reverberation.
Attack Gain 0–9 Adjusts the gain of the early reflections.
Attack Time 0–9 Adjusts the time of the early reflections.
ER Density 0–9
Adjusts the density of the early
reflections.
ER Level 0–99
Adjusts the volume of the early
reflections.
Low Freq 0.04–1.00 [kHz] Frequency of the low range.
Low Gain -24–+12 [dB] Gain of the low frequency range.
Mid Freq 0.25–9.99 [kHz]
Adjusts the amount of mid-frequency
boost/cut.
Mid Gain -24–+12 [dB]
Specifies the reference frequency of the
mid-frequency range.
Mid Q 0.2–9.0
Specifies the width of the mid-frequency
range.
Set a higher value for Q to narrow the
range to be affected.
High Freq 0.80–9.99 [kHz] Frequency of the high range.
High Gain -24–+12 [dB] Gain of the high frequency range.
HIGH Q 0.2–9.0
Specifies the width of the high-frequency
range.
Set a higher value for Q to narrow the
range to be affected.
GM2 REVERB
Parameter Value Explanation
Character 0–5 Type of reverb
Time
0–127 Time length of reverberation