Roland AX-EDGE, Parameter Manual

Page: 32 / 72

SYSTEM EFFECT Parameters
32
MASTER EQ
Parameter
[
K
] [
J
] button
Value
[-] [+] Buttons
Explanation
Switch OFF, ON
Specifies whether the master EQ (an
equalizer applied to the entire sound
generator of the AX-Edge) is used (ON) or
not used (OFF).
In Gain
(Input Gain)
-24–+24 [dB]
Adjusts the amount of boost/cut for the
input to the EQ.
Lo Gain
(Low Gain)
-24–+24 [dB] Gain of the low frequency range.
Lo Freq
(Low Frequency)
20–16000 [Hz] Frequency of the low range.
Mid1 Gain
(Mid1 Gain)
-24–+24 [dB] Gain of the middle frequency range 1.
Mid1Freq
(Mid1 Frequency)
20–16000 [Hz] Frequency of the middle range 1.
Mid1 Q
(Mid1 Q)
0.5–16.0
Width of the middle frequency range
1.Set a higher value for Q to narrow the
range to be affected.
Mid2 Gain
(Mid2 Gain)
-24–+24 [dB] Gain of the middle frequency range 2.
Mid2Freq
(Mid2 Frequency)
20–16000 [Hz] Frequency of the middle range 2.
Mid2 Q
(Mid2 Q)
0.5–16.0
Width of the middle frequency range
2.Set a higher value for Q to narrow the
range to be affected.
Mid3 Gain
(Mid3 Gain)
-24–+24 [dB] Gain of the middle frequency range 3.
Mid3 Freq
(Mid3 Frequency)
20–16000 [Hz] Frequency of the middle range 3.
Mid3 Q
(Mid3 Q)
0.5–16.0
Width of the middle frequency range
3.Set a higher value for Q to narrow the
range to be affected.
High Gain
(High Gain)
-24–+24 [dB] Gain of the high frequency range.
HighFreq
(High Frequency)
20–16000 [Hz] Frequency of the high range.
CHORUS Parameters
NOTE
The SYSTEM EFFECT chorus cannot be edited if the currently selected
program’s CHORUS Src is set to “PRG” (the settings are specified by the
program sound parameters). You can either edit the chorus settings for
the program, or change Src to
“SYS”
and edit them.
CHORUS
This is a stereo chorus.
Parameter Value Explanation
Rate
0–127 Frequency of modulation
Depth 0–127 Depth of modulation
Feedback 0–127
Level at which chorus sound is returned
to the input
CE-1
This models the classic BOSS CE-1 chorus effect unit. It provides a
chorus sound with a distinctively analog warmth.
Parameter Value Explanation
Intensity
0–127 Chorus depth
SDD-320
This models Roland’s DIMENSION D (SDD-320). It provides a clear
chorus sound.
Parameter Value Explanation
Mode 1–4, 1+4, 2+4, 3+4 Switches the mode.
DELAY
This is a stereo delay.
Parameter Value Explanation
Dly Sync
(sync sw)
OFF, ON
If this is ON, the delay synchronizes with
the tempo.
Dly Msec
(msec)
Dly Note
(note)
1–1300 [msec]
Adjusts the delay time from the direct
sound until the delay sound is heard.
Note
&
“Note” (p. 72)
Feedback -98–+98 [%]
Adjusts the proportion of the delay sound
that is fed back into the effect.
Negative (-) settings will invert the phase.
HF Damp
200–8000 [Hz],
BYPASS
Adjusts the frequency above which
sound fed back to the effect is filtered
out. If you don’t want to filter out any
high frequencies, set this parameter to
BYPASS.
T-CTRL DELAY
A stereo delay in which the delay time can be varied smoothly.
Parameter Value Explanation
Dly Sync
(sync sw)
OFF, ON
If this is ON, the delay synchronizes with
the tempo.
Dly Msec
(msec)
Dly Note
(note)
1–1300 [msec]
Adjusts the delay time from the direct
sound until the delay sound is heard.
Note
&
“Note” (p. 72)
Acceleration 0–15
When you change the delay time, this
specifies the time over which the current
delay time changes to the specified
delay time. This affects the speed of pitch
change as well as the delay time.
Feedback -98–+98 [%]
Adjusts the proportion of the delay sound
that is fed back into the effect.
Negative (-) settings will invert the phase.