Rohde & Schwarz SMCVB-K168 Page 34 User Manual Download

Page: 34 / 91

DVB-S2 Configuration and Settings

R&S

SMCVB-K168

User Manual 1179.1064.02 ─ 03

Modulation coding value

Implementation description

Bit interleaver
pattern

Required FEC
frame

81: 16APSK 32/45 Sx

4+12APSK 32/45

0123

Short

82: 32APSK 2/3 Sx

4+12+16rbAPSK 2/3

41230

Short

83: 32APSK 32/45 Sx

4+12+16rbAPSK 32/45

10423

Short

Table 3-5: S2-X family for VL-SNR

Modulation coding value

Implementation description

Required FEC frame

84: VL1 QPSK 2/9 Sx VL-SNR *

QPSK 2/9

Normal

85: VL1 BPSK 1/5 Sx VL-SNR **

/2 BPSK 1/5

Medium

86: VL1 BPSK 11/45 Sx VL-SNR **

/2 BPSK 11/45

Medium

87: VL1 BPSK 1/3 Sx VL-SNR **

/2 BPSK 1/3

Medium

88: VL1 BPSK-S 1/5 Sx VL-SNR

/2 BPSK 1/5

Spreading factor 2

Short

89: VL1 BPSK-S 11/45 Sx VL-SNR

/2 BPSK 11/45

Spreading factor 2

Short

90: VL2 BPSK 1/5 Sx VL-SNR

/2 BPSK 1/5

Short

91: VL2 BPSK 4/15 Sx VL-SNR

/2 BPSK 4/15

Short

92: VL2 BPSK 1/3 Sx VL-SNR

/2 BPSK 1/3

Short

For all members of this family, the pilot is enabled (fixed setting).

* For "84: VL1 QPSK 2/9 Sx VL-SNR", the symbol rate is restricted.

** For 85, 86, 87: VL1 Pi/2 BPSK 1/5, 11/45, 1/3 (medium FEC frame) Sx VL-SNR", padding is performed.

FEC Frame

Sets the length of the FEC frames.

Note:

The setting for time slice

1 is displayed on this side tab, the settings for all time

slices

> 1 are available on the "TSL 2 - x" side tab. See

Chapter 3.3.3, "IS 2 - x Set-

tings"

on page 35.

Note:

Classical modulation coding: With "Short", not all modulation coding settings are

possible. See

" Mod. Cod."

on page 30.

FEC frame "Medium" is not available with classical modulation coding.

"Normal"

64800

bit

"Medium"

Requires "S2-X > On".
32400

bit

"Short"

16200

bit

Remote command:

[:SOURce<hw>]:BB:DVBS2:TSL<st>:IS<ch>:FECFrame

on page 70

Coding Settings

Summary of Contents for SMCVB-K168




























































































Search results

Summary of Contents for SMCVB-K168

Reviews:

Related manuals for SMCVB-K168

Brands by name

Popular brands

Rohde & Schwarz SMCVB-K168, User Manual

Search results

Summary of Contents for SMCVB-K168

Reviews:

Related manuals for SMCVB-K168

Brands by name

Popular brands