Rohde & Schwarz CMW-B400B User Manual Download

Page: 36 / 97

GUI Reference

R&S

CMW-B400B/-B405A

User Manual 1176.8116.02 ─ 04

Window Type

Spectral Leakage

Amplitude Accuracy

Frequency Resolution

Rectangular

Poor

Best

Hamming

Fair

Good

Hann (Hanning)

Good

Fair

Good

Blackman-Harris

Best

Good

Fair

Flat-Top

Good

Best

Poor

Remote command:

CONFigure:AUDio:MEAS:ANALog:SINGletone:FILTer:WFUNction
CONFigure:AUDio:MEAS:DIGital:SINGletone:FILTer:WFUNction

Filter > Low Pass, High Pass, Weighting, Variable Bandpass

The settings configure the individual filter stages of the AF analyzer. For a description
of the filter types, see

chapter 3.3, "AF Filter Settings"

on page 16.

Remote command:
Analog measurement:

CONFigure:AUDio:MEAS:ANALog:SINGletone:FILTer:LPASs
CONFigure:AUDio:MEAS:ANALog:SINGletone:FILTer:HPASs
CONFigure:AUDio:MEAS:ANALog:SINGletone:FILTer:WEIGhting
CONFigure:AUDio:MEAS:ANALog:SINGletone:FILTer:BANDpass

Digital measurement:

CONFigure:AUDio:MEAS:DIGital:SINGletone:FILTer:LPASs
CONFigure:AUDio:MEAS:DIGital:SINGletone:FILTer:HPASs
CONFigure:AUDio:MEAS:DIGital:SINGletone:FILTer:WEIGhting
CONFigure:AUDio:MEAS:DIGital:SINGletone:FILTer:BANDpass

Limits (Analog Measurement)

This section configures upper or lower limits for most single tone results displayed in
the result table.

By default all limits are disabled.

Remote command:

CONFigure:AUDio:MEAS:ANALog:SINGletone:LIMit

Limits (Digital Measurement)

This section configures upper or lower limits for most single tone results displayed in
the result table.

By default all limits are disabled.

Audio Measurement Settings

深圳德标仪器

135-1095-0799

Summary of Contents for CMW-B400B


































































































Search results

Summary of Contents for CMW-B400B

Reviews:

Related manuals for CMW-B400B

Brands by name

Popular brands

Rohde & Schwarz CMW-B400B, User Manual

Search results

Summary of Contents for CMW-B400B

Reviews:

Related manuals for CMW-B400B

Brands by name

Popular brands