manualshive.com logo in svg

Rohde & Schwarz 1411.4002K02, Quick Start Manual

Share
Download
Rohde & Schwarz 1411.4002K02 Quick Start Manual Download Page 85

Manual Operation

R&S

®

SMC100A

70

Quick Start Guide 1411.4077.62 ─ 07

Table 4-1: List of the automatically assigned file extensions in the instrument

Function

List type

Contents

File suffix

Instrument State

Settings

Instrument settings

*.savrcltxt

"User Correction"

List

User-defined level correction values

*.uco

 

 

Export Data

*.txt

 or 

*.csv

 

 

 

 

NRP Settings

Settings

NRP Settings

*.nrp

4.8 Legend of Front-Panel Controls

The following table lists all key functions available on the front panel. Key combinations
used on the PC keyboard to trigger key functions on the instrument front panel are also
described. Keyboard labels are described in alphabetical order.

In addition, a front panel key emulation and an on-screen keyboard can be used for
manual operation by mouse only.

Table 4-2: Cross-reference between the front panel keys and keyboard shortcuts

Front-panel key

Key of PC keyboard

Function

Turning the rotary
knob

Tab key (towards the right)

Shift + Tab (towards the left)

Sets the cursor with the rotary knob.

Pressing the rotary
knob

Enter

Pressing the rotary knob confirms an entry; it has
the same function as the ENTER key.

Arrow keys

Arrow keys

Moves the cursor.

ENTER / dB(m)

Enter

ALT + F12

Terminates an entry.

Confirms entries in the base unit and values with-
out a unit.

Selects dBm for the RF level and dB for level offset
and level step width.

. / *...#

. / *...#

Enters a period/decimal point. Enters a special
character.

- / A<->a

- / (shift+) a—z

Enters the sign.

Switches between upper-case and lower-case let-
ters.

0-9 / a...z

CTRL+ 0-9 / a...z CTRL

Enters the number/letter.

BACKSPACE

Backspace

Clears the last entry (number, sign or decimal
point)

ESC / CLOSE

ESC / CTRL + G

Selects the next higher menu/selection level. When
the editing mode is exited with ESC, the previous
value is restored.

Closes an active menu.

DIAGR

CTRL+ D

Sets the cursor on the block diagram and hides all
menus.

 

Legend of Front-Panel Controls

Summary of Contents for 1411.4002K02



























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands