Rohde & Schwarz 1411.4002K02 Page 25 Quick Start Manual Download

Page: 25 / 90

Preparing for Use

R&S

SMC100A

Quick Start Guide 1411.4077.62 ─ 07

Figure 2-1: Front panel view

2.1.1 Utility Keys

The keys to the left of the display cause the R&S

SMC to return to a definite instrument

state and provide information on the instrument and assistance.

For more information refer to chapter "Instrument Settings" in the Operating Manual.

PRESET

Sets the instrument to a defined state (see

Chapter 2.3.5.4, "Default Settings"

on page 23).

LOCAL

Switches from remote control to local (manual) control.

SETUP

Opens the "Setup" dialog for configuring presettings.

HELP

Displays context-sensitive help text.

2.1.2 Standby LEDs and Standby Key

Front Panel Tour

Summary of Contents for 1411.4002K02



























































































Search results

Summary of Contents for 1411.4002K02

Reviews:

Related manuals for 1411.4002K02

Brands by name

Popular brands

Rohde & Schwarz 1411.4002K02, Quick Start Manual

Search results

Summary of Contents for 1411.4002K02

Reviews:

Related manuals for 1411.4002K02

Brands by name

Popular brands