manualshive.com logo in svg

Rohde & Schwarz 1330.5000K04, Getting Started

Share
Download
Rohde & Schwarz 1330.5000K04 Getting Started Download Page 44

Instrument Tour

R&S

®

FSVA3000/R&S

®

FSV3000

44

Getting Started 1330.8073.02 ─ 07

For details on configuring and using power sensors, see the R&S

 

FSV/A User

Manual.

5.1.11

 

Ext Mixer Connector (Optional)

Connect external mixers to the Ext Mixer IF In and LO Out / IF In female connec-
tors to increase the available frequency range. These connectors are optional and
only available with R&S

 

FSV3-B21.

If no external mixers are connected to the R&S

 

FSV/A, cover the two front con-

nectors Ext Mixer IF In and LO Out / IF In with the supplied SMA caps.

5.1.12

 

Noise Source Control / Power Sensor

The LEMOSA female connector is used to connect smart noise sources or
Rohde

 

&

 

Schwarz power sensors. For a detailed list of supported noise sources

and power sensors, see the data sheet.

Using power sensors requires option R&S

 

FSV3-K9.

For details on configuring and using noise sources and power sensors, see the
user manual.

5.1.13

 

AF Out and Volume (R&S

 

FSV3-B3)

This option allows you to monitor demodulated audio frequencies in time domain
measurements acoustically.

The AM and FM audio output is provided to the AF Out connector.

Connect headphones equipped with a miniature jack plug to the AF Out female
connector. Set the output voltage using the "Volume" control above the female
connector.

See also 

"Connecting headphones"

 

on page 9.

5.1.14

 

Keypad

The keypad is used to enter alphanumeric parameters, including the correspond-
ing units (see also 

Chapter 7.3.2, "Entering Alphanumeric Parameters"

,

on page 96). It contains the following keys:

Front Panel View

Summary of Contents for 1330.5000K04






















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands