Rockwell powerflex 700h Programming Manual Download Page 75

Page: 75 / 104

HIM Overview

A-5

Viewing and Editing
Parameters

LCD HIM

Numeric Keypad Shortcut

If using a HIM with a numeric keypad, press the ALT key and the +/– key to
access the parameter by typing its number.

Step

Key(s)

Example Displays

1. In the Main Menu, press the Up Arrow or

Down Arrow to scroll to “Parameter.”

2. Press Enter. “FGP File” appears on the top

line and the first three files appear below it.

3. Press the Up Arrow or Down Arrow to

scroll through the files.

4. Press Enter to select a file. The groups in

the file are displayed under it.

5. Repeat steps 3 and 4 to select a group

and then a parameter. The parameter
value screen will appear.

6. Press Enter to edit the parameter.

7. Press the Up Arrow or Down Arrow to

change the value. If desired, press Sel to
move from digit to digit, letter to letter, or
bit to bit. The digit or bit that you can
change will be highlighted.

8. Press Enter to save the value. If you want

to cancel a change, press Esc.

9. Press the Up Arrow or Down Arrow to

scroll through the parameters in the group,
or press Esc to return to the group list.

Sel

Esc

FGP:

Par 55

Maximum Freq

60.00

25 <> 400.00

FGP:

Par 55

Maximum Freq

90.00

25 <> 400.00

P: Group

Motor Data

Torq Attributes

Volts per Hertz

: Parameter

Maximum Voltage

Maximum Freq

Compensation

GP: File

Monitor

Motor Control

Speed Reference

Summary of Contents for powerflex 700h









































































































Search results

Summary of Contents for powerflex 700h

Reviews:

Related manuals for powerflex 700h

Brands by name

Popular brands

Rockwell powerflex 700h, Programming Manual

Search results

Summary of Contents for powerflex 700h

Reviews:

Related manuals for powerflex 700h

Brands by name

Popular brands