manualshive.com logo in svg

Rockwell Automation PowerFlex 750-Series, User Manual

Share
Download
Rockwell Automation PowerFlex 750-Series User Manual Download Page 81

Troubleshooting

7-3

 

 

 

PowerFlex 750-Series Drive DeviceNet Option Module User Manual

Publication 750COM-UM002A-EN-P

MOD Status Indicator

Status

Cause

Corrective Action

Off

The Option Module is not powered 
or is not properly connected to the 
drive.

•

Securely connect and ground the Option 
Module to the drive by fully inserting it into the 
drive port and tightening its two captive 
screws to the recommended torque.

•

Apply power to the drive.

Flashing 
Red

The Option Module has failed the 
firmware test.

The Option Module is being flash 
upgraded.

•

Clear faults in the Option Module.

•

Cycle power to the drive.

•

If cycling power does not correct the problem, 
the Option Module parameter settings may 
have been corrupted. Reset defaults and 
reconfigure the Option Module.

•

If resetting defaults does not correct the 
problem, flash the Option Module with the 
latest firmware release.

Solid 
Red

The Option Module has failed the 
hardware test.

•

Cycle power to the drive.

•

Replace the Option Module.

Flashing 
Green

The Option Module is operational, 
but is not transferring I/O data.

•

Place the scanner in RUN mode.

•

Program the controller to recognize and 
transmit I/O to the Option Module.

•

Configure the Option Module for the program 
in the controller.

•

Normal behavior if no I/O is being transferred.

Solid 
Green

The Option Module is operational 
and transferring I/O data.

No action required.

Summary of Contents for PowerFlex 750-Series

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands