manualshive.com logo in svg

Rockwell Automation PowerFlex 750-Series, User Manual

Share
Download
Rockwell Automation PowerFlex 750-Series User Manual Download Page 108

C-14

DeviceNet Objects

 

 

 

PowerFlex 750-Series Drive DeviceNet Option Module User Manual

Publication 750COM-UM002A-EN-P

19

Get

International DPI Online 
Parameter Text

Struct of:

STRINGN
STRINGN

International parameter name
International online units

20

Get

International DPI Online 
Read Full

Struct of:

BOOL[32]
CONTAINER
CONTAINER
CONTAINER
CONTAINER
UINT
UINT
UINT
UINT
UINT
INT
USINT[3]
USINT
BOOL[32]
STRINGN
STRINGN

Descriptor
Parameter value
Online minimum value
Online maximum value
Online default value
Next
Previous
Multiplier
Divisor
Base
Offset
Link
Pad word (always zero)
Extended descriptor
International parameter name
International online parameter units

21

Get

DPI Extended Descriptor

UDINT

Extended Descriptor (see page 

C-16

)

22

Get

International DPI Offline 
Read Full

Struct of:

BOOL
CONTAINER
CONTAINER
CONTAINER
UINT
UINT
UINT
UINT
UINT
UINT
UINT
USINT
USINT
UINT
UINT
CONTAINER
UINT
UINT
UINT
INT
BOOL[32]
STRINGN
STRINGN

Descriptor
Offline minimum value
Offline maximum value
Offline default value
Online minimum parameter instance
Online maximum parameter instance
Online default parameter instance
Multiplier parameter instance
Divisor parameter instance
Base parameter instance
Offset parameter instance
Formula number
Pad word (always zero)
Help instance
Pad word (always a value of zero)
Parameter value
Multiplier
Divisor
Base
Offset
Extended DPI descriptor
International DPI parameter name
International DPI offline parameter units

(1)

A CONTAINER is a 32-bit block of data that contains the data type used by a parameter value. If signed, the value is sign extended. Padding 
is used in the CONTAINER to ensure that it is always 32-bits.

(2)

This value is used in the formulas used to convert the parameter value between display units and internal units. Refer to 

Formulas for 

Converting on page C-17

.

(3)

Do NOT continually write parameter data to NVS. Refer to the attention on 

page 6-1

.

Attribute ID Access Rule Name

Data Type

Description

Summary of Contents for PowerFlex 750-Series

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands