manualshive.com logo in svg

Rockwell Automation Allen-Bradley PowerFlex 755T Series, Programming Manual, Page: 92 / 130

Share
Download
Rockwell Automation Allen-Bradley PowerFlex 755T Series Programming Manual Download Page 92

92

Rockwell Automation Publication 750-PM101B-EN-P - April 2022

Chapter 4          Troubleshooting

AC Precharge Circuit Board Status Indicators 

The PowerFlex 755T AC precharge module uses status indicators and a 7-
segment display to report conditions. See 

Figure 67 on page 93

 for the location 

of the AC precharge board.

Name

Color

State

Description

DS1 (AC Precharge)

Green

Flashing

Fiber connection is online.

Red

Flashing

Fiber connection is offline.

DS2 (240V AC)

Green

Steady

240V AC Okay

Yellow

Steady

240V AC Low Alarm

Red

Flashing

240V AC Loss Fault

Unlit

Off

240V AC Loss Alarm

DS3 (Communications)

Green

Steady

Fiber connection is online.

Yellow

Flashing

Communications Loss

Unlit

Off

Inactive

DS4 (AC Precharge)

Green

Steady

Precharge Done (Main circuit breaker is closed.)

Flashing

Main circuit breaker is closing.

Yellow

Steady

Main circuit breaker is opening.

Flashing

Not Ready

Red

Flashing

Main circuit breaker opened.

Unlit

Off

Ready

DS5 (Firmware Status)

Green

Steady

No faults or alarms are present.

Green / 

Red

Flashing 

Alternately

Update in progress.

Yellow

Steady

Alarm is present.

Red

Flashing

Fault is present.

7-Segment Display

Red

Steady

Normal Operation

• At powerup, the display indicates the major firmware revision 

number, the minor revision number, and the build number for 1 
second each.

• After powerup is complete, the display indicates the number 

that is assigned to the module by the main control board. 
(Shown: P0 = Precharge 0)

Alarms

• When an alarm condition exists, the display indicates the alarm 

code.

• If there are multiple alarm codes, the display cycles through the 

codes and displays each code for 2 seconds.

Flashing

Faults

• When a fault condition exists, the display indicates the fault 

code for Port 14.

• If there are multiple fault codes, the display cycles through the 

codes and displays each code for 2 seconds.

• If the device is faulted, the display only indicates fault codes. 

Alarm codes are omitted.

DS1

DS2

DS3

DS4

DS5

7-Segment Display

Input Bay

Summary of Contents for Allen-Bradley PowerFlex 755T Series



































































































































Reviews:

No comments