manualshive.com logo in svg

Rockwell Automation Allen-Bradley PowerFlex 755T Series, Programming Manual, Page: 88 / 130

Share
Download
Rockwell Automation Allen-Bradley PowerFlex 755T Series Programming Manual Download Page 88

88

Rockwell Automation Publication 750-PM101B-EN-P - April 2022

Chapter 4          Troubleshooting

Faults

A fault is a condition that stops the drive. There are four types of faults.

Alarms

An alarm is a condition that, if left unaddressed, can stop the drive if the drive 
running or does not allow you to start the drive. There are two types of alarms.

Events

Events occur under normal operation of the product. When an event occurs, 
the drive records an entry consisting of a numeric event code and a time stamp 
in an event queue. Events can help to troubleshoot problems.

Configurable Conditions

You can use a configuration parameter to set user-configurable conditions to 
either fault, alarm, or ignore.

Viewing Faults, Alarms, 

Events, and Exceptions

When a condition occurs, the drive records the occurrence in the fault, alarm, 
event, or exception queue. These queues are accessible through software or the 
HIM and provide you with a history of each type of occurrence. You can also 
access diagnostic file parameters for additional information.

•

Port 0: Diagnostics File, Status Group

•

Port 0: Diagnostics File, Fault/Alarm Info Group

•

Port 10: Diagnostics File, Status Group

•

Port 10: Diagnostics File, Fault/Alarm Info Group

•

Port 13: Diagnostics File, Status Group

•

Port 13: Diagnostics File, Fault/Alarm Info Group

Type

Description

Major Fault

If this type of fault occurs while the line side converter or motor side inverter is modulating, it 

stops modulating. If it occurs while the line side converter or motor side inverter is not 

modulating, it prevents starting. It prevents starting until the fault is cleared.

Minor Fault

If this type of fault occurs while the line side converter or motor side inverter is modulating, it 

allows modulation to continue. If it occurs while the line side converter or motor side inverter 

is not modulating, it prevents starting. It prevents starting until the fault is cleared.

Resettable

This type of fault can be cleared. Resettable faults are identified by ‘Resettable Fault’.

Non-resettable

This type of fault normally requires drive or motor repair. You must correct the cause of the 

fault before the fault can be cleared. The fault will be reset on powerup after repair. Non-

resettable faults are identified by ‘Non-Reset Fault’.

Type

Description

Alarm 1

Alarms of type 1 indicate that a condition exists. Type 1 alarms are user configurable.

Alarm 2

Alarms of type 2 indicate that a configuration error exists and the drive cannot be started. 

Type 2 alarms are not configurable.

Type

Description

Configurable

Options can include:

‘Ignore’ (0) – No action is taken. 

(1)

‘Alarm’ (1) – Type 1 alarm indicated.

‘Flt Minor’ (2) – Minor fault indicated. If running, drive continues to run.

‘FltCoastStop’ (3) – Major fault indicated. Coast to Stop.

‘Flt RampStop’ (4) – Major fault indicated. Ramp to Stop.

‘Flt CL Stop’ (5) – Major fault indicated. Current Limit Stop.

(1) When ‘Ignore’ (0) is the default setting, the occurrence is recorded in the exceptions queue. When you set a configuration 

parameter to ‘Ignore’ (0), the occurrence is recorded in the event queue.

Summary of Contents for Allen-Bradley PowerFlex 755T Series



































































































































Reviews:

No comments