manualshive.com logo in svg

Rockwell Automation Allen-Bradley PowerFlex 755T Series, Programming Manual, Page: 113 / 130

Share
Download
Rockwell Automation Allen-Bradley PowerFlex 755T Series Programming Manual Download Page 113

Rockwell Automation Publication 750-PM101B-EN-P - April 2022

113

Chapter 4          Troubleshooting

Recovery Mode

The TotalFORCE control platform has a recovery mode. Recovery mode 
recreates the product file system and all parameter data is defaulted. Use the 
following procedure if the processor fails to start up.

Recovery Mode Procedure

1. Power down the product.
2. Locate the three IP address Switches on the main control board.
3. Record the positions of the switches so they can be set back to these 

positions at the end of the procedure.

4. Set all three switches to position 8, for an overall value of 888.

5. Power up the product.
6. Wait for the STS indicator to turn flashing red and the ENET indicator to 

turn steady red.

7. Power down the product.
8. Set the tens position switch to position 9 and the ones position switch to 

position 7, for an overall value of 897.

9. Power up the product.
10. Wait for the STS indicator to turn flashing red and ENET indicator to 

turn steady red.

11. Power down the product.
12. Set the IP address switches to the positions recorded in step 3.
13. Power up the product.

Hundreds Position

Tens Position

Ones Position

Ones 
Position

Hundreds 
Position

Tens 
Position

Ones 
Position

Hundreds 
Position

Tens 
Position

Summary of Contents for Allen-Bradley PowerFlex 755T Series



































































































































Reviews:

No comments