manualshive.com logo in svg

Rockwell Automation Allen-Bradley PowerFlex 755T Series, Programming Manual, Page: 112 / 130

Share
Download
Rockwell Automation Allen-Bradley PowerFlex 755T Series Programming Manual Download Page 112

112

Rockwell Automation Publication 750-PM101B-EN-P - April 2022

Chapter 4          Troubleshooting

Reset as Shipped

The TotalForce control platform can be reset as shipped using the IP address 
rotary switches. All parameter data is defaulted. Use the following procedure 
to perform a reset as shipped.

Reset as Shipped Procedure

1. Power down the product.
2. Locate the three IP address switches on the main control board.
3. Record the positions of the switches so they can be set back to these 

positions at the end of the procedure. 

4. Set all three switches to position 8, for an overall value of 888.

5. Power up the product.

Wait for the STS indicator to turn flashing red and the ENET indicator to 
turn solid red.

6. Power down the product.
7. Set the IP address switches to the positions recorded in step 3.
8. Power up the product.

Hundreds Position

Tens Position

Ones Position

Ones 
Position

Hundreds 
Position

Tens 
Position

Summary of Contents for Allen-Bradley PowerFlex 755T Series



































































































































Reviews:

No comments