manualshive.com logo in svg

Rockwell Automation Allen-Bradley PowerFlex 755T Series, Programming Manual, Page: 103 / 130

Share
Download
Rockwell Automation Allen-Bradley PowerFlex 755T Series Programming Manual Download Page 103

Rockwell Automation Publication 750-PM101B-EN-P - April 2022

103

Chapter 4          Troubleshooting

Incorrect digital input programming.

• Mutually exclusive choices have been made 

(for example, Jog and Jog Forward)

• 2-wire and 3-wire programming may be 

conflicting

• Start configured without a Stop configured

None

Configure input function.

Flashing yellow status 

light and ‘DigIn Cnfg B’

or

‘DigIn Cnfg C’ indication on 

LCD HIM.

10:355 [Motor Side Sts 2] 

shows type 2 alarm(s).

Resolve input function conflicts.

Terminal block does not have control.

None

Check 0:41 [Logic Mask].

Drive does not Start from HIM.

Cause(s)

Indication

Corrective Action

Drive is configured for 2-wire level control.

None

Change 0:101 [Digital In Cfg] to correct 

control function.

Another device has Manual control.

None

—

Port does not have control.

None

Change 0:41 [Logic Mask] to enable 

correct port.

Drive does not respond to changes in speed command.

Cause(s)

Indication

Corrective Action

No value is coming from the source of the 

command.

LCD HIM Status Line 

indicates ‘At Speed’ and 

output is 0 Hz.

• If the source is an analog input, 

check wiring and use a meter to 

check for presence of signal

Incorrect reference source has been 

programmed.

None

• Check 10:1800 [VRef A Sel] for the 

source of the speed reference

• Reprogram 10:1800 [VRef A Sel] for 

correct source

Incorrect Reference source is being selected 

via remote device or digital inputs.

None

• Check 10:354 [Motor Side Sts 1], bits 

12 and 13 for unexpected source 

selections

• Check 0:100 [Digital In Sts], to see if 

inputs are selecting an alternate 

source

• Check configuration of 

173…175 [DI Speed Sel

n

] functions

Motor and/or drive will not accelerate to commanded speed.

Cause(s)

Indication

Corrective Action

Acceleration time is excessive.

None

Reprogram 10:1915/

1916 [VRef Accel Time

n

].

Excess load or short acceleration times force 

the drive into current limit, slowing or 

stopping acceleration.

None

Check 10:354 [Motor Side Sts 1], bit 27 

to see if the drive is in Current Limit.

Remove excess load or reprogram 

10:1915/1916 [VRef Accel Time

n

].

Speed command source or value is not as 

expected.

None

Check for the proper Speed Command 

using Steps 1 through 7 above.

Programming is preventing the drive output 

from exceeding limiting values.

None

Check 10:1898 [Vel Limit Pos], 

10:1899 [Vel Limit Neg], and 

10:422 [Maximum Freq] to assure that 

speed is not limited by programming.

Motor operation is unstable.

Cause(s)

Indication

Corrective Action

Motor data was incorrectly entered or 

Autotune was not performed.

None

1. Correctly enter motor nameplate 

data.

2. Perform ‘Static Tune’ or ‘Rotate Tune’ 

Autotune procedure. See parameter 
10:910 [Autotune].

Drive does not start from Start or Run inputs that are wired to the terminal block.

Cause(s)

Indication

Corrective Action

Summary of Contents for Allen-Bradley PowerFlex 755T Series



































































































































Reviews:

No comments