Rockwell Automation Allen-Bradley PowerFlex 4 User Manual Download Page 34

Page: 34 / 94

2-2

Start Up

Applying Power to the Drive

❏

Apply AC power and control voltages to the drive.

❏

Familiarize yourself with the integral keypad features (see

page 2-3

)

before setting any Program Group parameters.

Start, Stop, Direction and Speed Control

Factory default parameter values allow the drive to be controlled from
the integral keypad. No programming is required to start, stop, change
direction and control speed directly from the integral keypad.

Important:

To disable reverse operation, see A095

[Reverse Disable]

If a fault appears on power up, refer to

Fault Descriptions on page 4-3

for an explanation of the fault code.

userman.book Page 2 Friday, June 21, 2002 2:48 PM

Summary of Contents for Allen-Bradley PowerFlex 4































































































Search results

Summary of Contents for Allen-Bradley PowerFlex 4

Reviews:

Brands by name

Popular brands

Rockwell Automation Allen-Bradley PowerFlex 4, User Manual

Search results

Summary of Contents for Allen-Bradley PowerFlex 4

Reviews:

Brands by name

Popular brands