manualshive.com logo in svg

Rockwell Automation Allen-Bradley PowerFlex 4, User Manual

Share
Download
Rockwell Automation Allen-Bradley PowerFlex 4 User Manual Download Page 33

Chapter

 2

Start Up

This chapter describes how to start up the PowerFlex 4 Drive. To 
simplify drive setup, the most commonly programmed parameters are 
organized in a single Basic Program Group.

Important:

Read the 

General Precautions

 section before proceeding

.

Before Applying Power to the Drive

❏

1.

Confirm that all inputs are connected to the correct terminals and are 
secure.

❏

2.

Verify that AC line power at the disconnect device is within the rated 
value of the drive.

❏

3.

Verify that any digital control power is 24 volts.

❏

4.

Verify that the Sink (SNK)/Source (SRC) Setup DIP Switch is set to 
match your control wiring scheme. See 

Figure 1.5 on page 1-13

 for 

location.

Important:

The default control scheme is Source (SRC). The Stop 
terminal is jumpered (I/O Terminals 01 and 11) to allow 
starting from the keypad. If the control scheme is changed 
to Sink (SNK), the jumper must be removed from I/O 
Terminals 01 and 11 and installed between I/O Terminals 
01 and 04.

❏

5.

Verify that the Stop input is present or the drive will not start.

Important:

If I/O Terminal 01 is used as a stop input, the jumper 
between I/O Terminals 01 and 11 must be removed.

!

ATTENTION:  

Power must be applied to the drive to perform the 

following start-up procedures. Some of the voltages present are at 
incoming line potential. To avoid electric shock hazard or damage to 
equipment, only qualified service personnel should perform the 
following procedure. Thoroughly read and understand the procedure 
before beginning. If an event does not occur while performing this 
procedure, 

Do Not Proceed

. 

Remove All Power

 including user 

supplied control voltages. User supplied voltages may exist even when 
main AC power is not applied to the drive. Correct the malfunction 
before continuing.

Prepare For Drive Start-Up

userman.book  Page 1  Friday, June 21, 2002  2:48 PM

Summary of Contents for Allen-Bradley PowerFlex 4































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands