manualshive.com logo in svg

Rockwell Automation Allen-Bradley PowerFlex 4, User Manual

Share
Download
Rockwell Automation Allen-Bradley PowerFlex 4 User Manual Download Page 26

1-16

Installation/Wiring

Typical Multiple Drive Connection Examples

3 Wire SRC Control - 
Reversing

P036 

[Start Source]

 = 1

A momentary input will 
start the drive. A stop 
input to I/O Terminal 01 
will stop the drive as 
specified by P037 

[Stop 

Mode]

. I/O Terminal 03 

determines direction.

Internal Supply (SRC)

External Supply (SRC)

3 Wire SNK Control - 
Reversing

Internal Supply (SNK)

Input

Connection Example

11

01

02

03

Stop

Start

Direction

+24V

Common

Stop

Start

Direction

01

02

03

04

Stop

Start

Direction

01

02

03

04

Input

Connection Example

Multiple Digital Input 
Connections

Customer Inputs can be 
wired per External Supply 
(SRC) or Internal Supply 
(SNK) examples on 

page 1-15

.

When connecting a single input such as Run, Stop, Reverse or Preset 
Speeds to multiple drives, it is important to connect I/O Terminal 04 
common together for all drives. If they are to be tied into another common 
(such as earth ground or separate apparatus ground) only one point of 
the daisy chain of I/O Terminal 04 should be connected.

Multiple Analog 
Connections

When connecting a single potentiometer to multiple drives it is important 
to connect I/O Terminal 14 common together for all drives. I/O Terminal 14 
common and I/O Terminal 13 (potentiometer wiper) should be 
daisy-chained to each drive. All drives must be powered up for the analog 
signal to be read correctly.

04

Customer Inputs

Optional Ground Connection

02

04

02

04

02

04

02

Remote Potentiometer

Optional Ground Connection

12 13 14

13 14

13 14

13 14

Each digital input draws 6 mA.

userman.book  Page 16  Friday, June 21, 2002  2:48 PM

Summary of Contents for Allen-Bradley PowerFlex 4































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands