Rockwell Automation 9VT201-007HTNNN User Manual Download Page 135

Page: 135 / 224

Troubleshooting

4-5

Publication 9VT-UM001D-EN-P

Decel Inhibit

➂

The drive is not following a
commanded deceleration
because it is attempting to limit
bus voltage.

1. Verify input voltage is within drive

specified limits.

2. Verify system ground impedance

follows proper grounding
techniques.

3. Disable bus regulation and/or

add dynamic brake resistor and/
or extend deceleration time.

Drive OverLoad

Drive rating of 110% for 1 minute
or 150% for 3 seconds has been
exceeded.

Reduce load or extend Accel Time.

Excessive Load

Motor did not come up to speed
in the allotted time during
autotune.

1. Uncouple load from motor.
2. Repeat Autotune.

FluxAmpsRef
Rang

The value for flux amps
determined by the Autotune
procedure exceeds the
programmed [Motor NP FLA].

1. Reprogram [Motor NP FLA] with

the correct motor nameplate
value.

2. Repeat Autotune.

Function Loss

Function loss input is open.

Check remote wiring.

Ground Fault

➀

A current path to earth ground
greater than 25% of drive rating.

Check the motor and external wiring
to the drive output terminals for a
grounded condition.

Heatsink
OvrTemp

➀

Heatsink temperature exceeds
100% of [Drive Temp].

1. Verify that maximum ambient

temperature has not been
exceeded.

2. Check fan.
3. Check for excess load.

HW OverCurrent

➀

The drive output current has
exceeded the hardware current
limit.

Check programming. Check for
excess load, improper DC boost
setting, DC brake volts set too high
or other causes of excess current.

Incompat
MCB-PB

106

➁

Drive rating information stored on
the power board is incompatible
with the main control board.

Load compatible version files into
drive.

I/O Comm Loss

121

I/O Board lost communications
with the Main Control Board.

Check connector. Check for induced
noise. Replace I/O board or Main
Control Board.

I/O Board Fail

122

Board failure.

Cycle power. If fault repeats, replace
I/O board.

I/O Mismatch

120

Incorrect I/O board identified.

Restore I/O board to original
configuration, or if new configuration
is desired, reset fault.

IR Volts Range

“Calculate” is the autotune
default and the value determined
by the autotune procedure for IR
Drop Volts is not in the range of
acceptable values.

Re-enter motor nameplate data.

Motor OverLoad

➀
➂

Internal electronic overload trip.
Enable/Disable with [Fault Config
1] on

page 3-50

An excessive motor load exists.
Reduce load so drive output current
does not exceed the current set by
[Motor NP FLA].

Fault

No.

)

Description

Action

Summary of Contents for 9VT201-007HTNNN

































































































































































































































Search results

Summary of Contents for 9VT201-007HTNNN

Reviews:

Rockwell Automation 9VT201-007HTNNN, User Manual, Page: 135 / 224

Search results

Summary of Contents for 9VT201-007HTNNN

Reviews: