Robustel GoFixed W800 User Manual Download Page 15 | Manualshive

Page: 15 / 60

Robustel GoFixed W800 User Manual Download Page 15

Robustel GoFixed W800 User Guide

RT_W800_UG_v02.00

04.11.2011

Page 14 /59

Confidential

negotiation
Solid   green: PPP/DHCP   up
Quick blinking green: Tx/Rx traffic on
line
On:   Modem   synchronized   to   the
DSLAM
Quick   blinking   green:   Modem
training, but   not   synchronized

DSL

Slow blinking green: Modem Idle
On: The analog phone connected to
VoIP off-‐hook

VoIP

Off: The analog phone connected to
VoIP on-‐hook
On: Wi-‐Fi connection   is available
Blinking green: Negotiation   or traffic
on   line

WiFi

Off: Wi-‐Fi connection is not available

WPS

Indicate   the   status   of   WPS
authenticator
Blinking green: Negotiation   or traffic
on   line
Solid   green: Up
Quick blinking green: Tx/Rx traffic on
line
Solid   red: Authentication   failed

3G

Off: Traffic through DSL interface

Power switch

Power

For 12V DC power adapter

LAN 1-‐4

LAN interface for connecting to
computers

VoIP

Connecting to analog telephones

Interface 1

DSL

Connecting

to

ADSL

enabled

telephone line

SIM

SIM Card slot

3G

3G Switch

Reset

Restore to factory default settings

Interface 2

WPS

WPS Switch

2.3

Install the Bracket

Mount the bracket on the bottom of the gateway.

«
...
13
14
15
16
17
...
»

Summary of Contents for GoFixed W800





























































Reviews:

No comments