Roborock S6 Series Faq Download Page 48

Page: 48 / 67

Roborock Customer Service Center - Technical Support

9. Q: What should I do when error 9 occurs?

A: Error 9 indicates that the machine has detected that the dust bin or filter is not installed: 1.

Reinstall the dust bin or filter if necessary. 2. If a non-Xiaomi filter purchased from a third party

is used, please buy a genuine filter from Xiaomi Store.

10. Q: What should I do when error 10 occurs? (Updated on August 10, 2018)

A: Error 10 indicates that the machine has detected that the filter is blocked: 1. If the dust bin

is full, empty the dust bin. 2. If the filter is blocked, please carefully clean the filter. 3. If the filter

has been used for more than 3 months, please replace it. 4. If the machine has accidentally

sucked up water or the filter has been washed with water, please replace the filter.

It is recommended that the user follow the description in the link when cleaning the filter.

Link:

https://www.youtube.com/watch?v=zL3ztCynHIY

11. Q: What should I do when error 11 occurs?

A: Error 11 indicates that the machine has detected an intense magnetic field when starting: 1.

The starting point may be too close to a barrier tape. Please move the machine and start it in

another place. 2. The machine has started near an intense magnetic field, such as a speaker

or floor-mounted socket. Please move the machine and start it in another place.

12. Q: What should I do when error 12 occurs?

A: Error 12 indicates that the battery level is too low. Please put the machine back onto the

dock charger to charge before use.

13. Q: What should I do when error 13 occurs?

A: Error 13 indicates a machine charging failure: 1. Poor contact results because the charging

area is dirty. Please clean the charging contact on the rear of the machine and the contact tab

of the dock charger after powering off and disconnecting the machine from the dock charger. 2.

Poor contact of the dock charger's power cable. Please check whether the power cable is

inserted in place. 3. The dock charger is placed on an uneven floor or on a carpet. Please place

the dock charger against a wall on a level and hard floor.

Summary of Contents for S6 Series




































































Search results

Summary of Contents for S6 Series

Reviews:

Related manuals for S6 Series

Brands by name

Popular brands

Roborock S6 Series, Faq

Search results

Summary of Contents for S6 Series

Reviews:

Related manuals for S6 Series

Brands by name

Popular brands