manualshive.com logo in svg

Roborock S6 Series, Faq

Share
Download
Roborock S6 Series Faq Download Page 40

Roborock Customer Service Center - Technical Support

 

 

40

 

 

12. Q: How long can cleaning logs be retained? (Updated on January 3, 2019)   

A: The cleaner only retains cleaning logs for seven days. The logs can be saved after being 

uploaded to the server. (Spot cleaning logs are not included in the cleaning logs.) 

13. Q: Can notifications be blocked from the app? 

A:  From  your  mobile  phone,  when  the  "Notification  ON/OFF"  switch  is  set  to  OFF,  any 

notification about the machine will be blocked. 

14. Q: Why is there a long delay when tapping a button in the app? 

A: When the machine runs in an area with poor Wi-Fi coverage, the command issued may fail 

or be delayed for a certain amount of time. In this case, this situation can be effectively improved 

by using a router with a higher signal strength or by using a signal amplifier. 

15. Q: What should I do when firmware update fails/stops? 

A: 1. Please update the Mi Home client to the latest version. An old client version may fail to 

normally display firmware update prompts. 2. If there is a poor network signal, downloading 

OTA  packages  may  fail  or  time  out.  Please  place  the  machine  and  dock  charger  near  your 

wireless router and try again. 3. Check that the machine is connected to the dock charger and 

charging and that the battery capacity is higher than 20%, and then try again. 4. If an update 

stops, please wait for another 20 minutes and then try again. 

16. Q: Is multi-router roaming supported? 

A: Yes, but please ensure that all routers use the same SSID (i.e. wireless signal name of these 

routers) and login password. Roaming among routers using different SSIDs and passwords is 

not supported. 

17. Q: Are Wi-Fi amplifiers/repeaters supported? 

A: Yes. 

18. Q: What's the 3G/4G traffic consumption for the mobile phone? 

A:  About  20  MB  of  traffic  is  required  per  hour  on  the  map  page,  with  almost  no  traffic 

Summary of Contents for S6 Series




































































Reviews:

No comments

Brands by name

Popular brands

Load more brands