manualshive.com logo in svg

Roborock S6 Series, Faq

Share
Download
Roborock S6 Series Faq Download Page 38

Roborock Customer Service Center - Technical Support

 

 

38

 

 

necessary to use the corresponding interface of the Mi Home app, which is something that the 

older  version  of  Mi  Home  does  not  have.  This  is  the  reason  this  problem  occurs.  This 

explanation is provided for customer service agents only. There is no need to explain this to 

users.) 

 

2. Q: What should I do when the machine frequently goes offline? 

A: 1. Please check that the machine works within the coverage of your router, especially when 

the machine works out of the Wi-Fi coverage range. 

2. Please check that the network of the broadband service provider works normally. 

3. Is timed rebooting of your router set up? 

3. Q: What should I do when the machine cannot be found in the Mi Home app? 

A: 1. Press and hold the Cleaning key and also the Recharge key until you are alerted with the 

"Reset Wi-Fi" voice prompt.   

2. Move your phone within 1 m of the machine, and then open the Mi Home app.   

3. Wait until the robotic vacuum cleaner is detected and then connect it to the Internet.   

4. Please check that the positioning permission for the Mi Home app is not disabled. 

4. Q: What should I do when the machine displays an inaccurate battery capacity? 

A: Please firstly charge it to 100% to calibrate it before use. The battery capacity displayed will 

be more accurate. 

5. Q: Why does the direction of the map frequently change? 

A: The map of the Mi Home robotic vacuum cleaner is generated in real time according to data 

collected  by  sensors  attached  to  the  machine  body.  The  map  generation  process  may  be 

affected when the environment changes. 

Therefore,  the  direction  of  the  generated  map  may  also  change  accordingly.  Please  rest 

assured that this will not influence the cleaning effect of the machine. 

Summary of Contents for S6 Series




































































Reviews:

No comments

Brands by name

Popular brands

Load more brands