ROBEL 62.05L Page 59 Operating Manual Download

Page: 59 / 151

9. Maintenance

9.6

Tamping tool

9.6.1

Checking the tamping tool for wear

To prevent a hole appearing in the bottom of the tamping pick
and oil escaping or to prevent damage to the bearing, regular
checks must be made prior to each use to see how much ma-
terial has already worn away.

NOTICE

Risk of damage to tamping pick!
the tamping tool is worn and the aluminium of the tamping
pick is visible, there is danger of holes forming.

►

As soon as aluminium is visible, you have to replace the
tamping tool.

Fig. 46: Measuring the length of the tamping tool

Measure the length of the tamping tool using a tape
measure.

New tamping tool: Length 40.5 cm
Worn tamping tool: Length <36 cm

As soon as the tamping tool is worn approx. 4.5 cm, it must
be replaced (see next page).

Summary of Contents for 62.05L
























































































































































Search results

Summary of Contents for 62.05L

Reviews:

Related manuals for 62.05L

Brands by name

Popular brands

ROBEL 62.05L, Operating Manual

Search results

Summary of Contents for 62.05L

Reviews:

Related manuals for 62.05L

Brands by name

Popular brands