ROBEL 62.05L Page 50 Operating Manual Download

Page: 50 / 151

9. Maintenance

9.3.2

Cleaning the fuel filter

WARNING

Risk of fire or explosion!
Petrol is extremely flammable and is explosive
under certain conditions.

►

Do not smoke or allow flames or sparks in
the working area.

Make sure that the engine oil filler cap on the four-stroke
engine is tightened securely.

Unscrew the fuel tank cap.

Carefully pull out the fuel filter from the fuel filler neck
using a wire.

Fig. 35: Cleaning the fuel filter

Fuel pipe

Hose clamp

Fuel filter

Check the fuel filter for any contamination. If it is contami-
nated wash it using a non-flammable solvent or one with a
high flash point. Replace the filter if it is contaminated ex-
cessively.

After checking, cleaning or replacing, fix the fuel filter onto
the fuel pipe with the hose clamp.

Re-insert the fuel filter into the fuel filler neck.

Push the filter in all the way to the bottom of the fuel tank.

Tighten the tank lid securely.

Summary of Contents for 62.05L
























































































































































Search results

Summary of Contents for 62.05L

Reviews:

Related manuals for 62.05L

Brands by name

Popular brands

ROBEL 62.05L, Operating Manual

Search results

Summary of Contents for 62.05L

Reviews:

Related manuals for 62.05L

Brands by name

Popular brands