User's Guide Fireface 400
© RME
59
30. Word Clock
30.1 Word Clock Input and Output
SteadyClock
guarantees an excellent performance in all clock modes. Based on the highly effi-
cient jitter suppression, the Fireface refreshes and cleans up any clock signal, and provides it
as reference clock at the BNC output (see section 37.9).
Input
The Fireface's transformer isolated word clock input is active when
Pref. Sync Ref
in the Set-
tings dialog has been switched to
Word Clock
, the clock mode
AutoSync
has been activated,
and a valid word clock signal is present. The signal at the BNC input can be Single, Double or
Quad Speed, the Fireface 400 automatically adapts to it. As soon as a valid signal is detected,
the WC LED is lit, and the Settings dialog shows either Lock or Sync (see chapter 37.1).
Thanks to RME's
Signal Adaptation Circuit
, the word clock input still works correctly even with
heavily mis-shaped, dc-prone, too small or overshoot-prone signals. Thanks to automatic signal
centering, 300 mV (0.3V) input level are sufficient in principle. An additional hysteresis reduces
sensitivity to 1.0 V, so that over- and undershoots and high frequency disturbances don't cause
a wrong trigger.
The Fireface's word clock input is shipped as high
impedance type (not terminated). A push switch al-
lows to activate internal termination (75 Ohms). The
switch is found on the back beside the word clock
input socket. Use a small pencil or similar and care-
fully push the blue switch so that it snaps into its lock
position. The yellow LED will be lit when termination is
active. Another push will release it again and de-
activate the termination.
Output
The word clock output of the Fireface is constantly active, providing the current sample fre-
quency as word clock signal. As a result, in Master mode the provided word clock is defined by
the currently used software. In Slave mode the provided frequency is identical to the one pre-
sent at the currently chosen clock input. When the current clock signal fails, the Fireface 400
switches to Master mode and adjusts itself to the next, best matching frequency (44.1 kHz, 48
kHz etc.).
Selecting
Single Speed
in the Settings dialog causes the output signal to always stay within the
range of 32 kHz to 48 kHz. So at 96 kHz and 192 kHz sample rate, the output word clock is 48
kHz.
The received word clock signal can be distributed to other devices by using the word clock out-
put. With this the usual T-adapter can be avoided, and the Fireface 400 operates as
Signal
Refresher
. This kind of operation is highly recommended, because
•
input and output are phase-locked and in phase (0°) to each other
•
SteadyClock removes nearly all jitter from the input signal
•
the exceptional input (1 Vpp sensitivity instead of the usual 2.5 Vpp, dc cut, Signal Adapta-
tion Circuit) plus SteadyClock guarantee a secure function even with highly critical word
clock signals
Thanks to a low impedance, but short circuit proof output, the Fireface delivers 4 Vpp to 75
Ohms. For wrong termination with 2 x 75 Ohms (37.5 Ohms), there are still 3.3 Vpp at the out-
put.
Summary of Contents for Fireface 400
