RKI Instruments GasWatch 3 Operator'S Manual Download Page 86

Page: 86 / 95

86 • Appendix A: Maintenance Mode

GasWatch 3 for CO and O

Turning the ID Display Function On/Off (ID DISP)

: The User ID and Station ID screens appear in the startup sequence. If

DISP.SET

in User

Mode is also set to

, then the IDs can be changed in Display Mode.

OFF

(factory setting): The User ID and Station ID screens do not appear in the startup

sequence and the IDs cannot be changed in Display Mode.
1. While in Maintenance Mode, press AIR to scroll to

ID DISP

2. Press and release POWER/MODE. The current setting flashes.
3. Use AIR to display the desired setting.
4. Press and release POWER/MODE to save the setting and return to the

ID DISP

item in

Maintenance Mode.

5. See “Entering Measuring Mode (START)” on page 90 to enter Measuring Mode.

Turning the Zero Suppression On/Off (ZERO.SUP)

The

ZERO.SUP

setting is not intended for field adjustment. The default setting is

Turning the Zero Follower On/Off (ZERO.FLW)

The

ZERO.FLW

setting is not intended for field adjustment. The default setting is

. The

oxygen channel does not support zero follower functionality.

User Mode Zero Suppression (ZSUP.DSP)

: Zero suppression item appears in User Mode.

OFF

(factory setting): Zero suppression item does not appear in User Mode. The zero

suppression item is always available in Maintenance Mode.
It is not normally necessary to have the zero suppression item appear in User Mode. Contact

RKI Instruments before turning this setting on.

Sensor

Zero Suppression

Value

2 ppm

0.5% volume

ID DISP

Summary of Contents for GasWatch 3
































































































Search results

Summary of Contents for GasWatch 3

Reviews:

Related manuals for GasWatch 3

Brands by name

Popular brands

RKI Instruments GasWatch 3, Operator'S Manual

Search results

Summary of Contents for GasWatch 3

Reviews:

Related manuals for GasWatch 3

Brands by name

Popular brands