Page 1 of 3
8 pcs.
email: [email protected]
FURNITURE
Riverside
6 pcs.
1 pc.
Hardware and Parts packed with the Queen Storage Footboard
F-A
F-E
F-F
2 pcs.
∅
5
16
-18 x 2-3/4" Long
Allen Head Bolt
8 pcs.
#8 x 1" Wood
Screw
F-G
Queen Storage
Footboard
Hardware and Parts packed with the 5/0-6/6 Bed Rails
8 pcs.
8 pcs.
∅
5
16
-18 x 3-1/2
" Long
All-Thread Bolt
8 pcs.
Queen / Eastern King
Bed Rail
2 pcs.
R-A
R-B
R-C
R-D
R-E
R-F
1 pc.
Ø
5
16
-18 Hex Nut
12mm Open Wrench
Slat Support Rails
Queen Roll Slat
(61" X 80-7/8")
1 pc.
F-B
2 pcs.
F-C
1 pc.
F-D
Slat Support Leg
Vogue Bed Room
Queen Bed
Assembly Instructions
∅
5
16
-18 x 1-1/2" Long
Allen Head Bolt
Ø
5
16
x 12 x 3mm
Spring Washer
Ø
5
16
x 19 x 2mm
Flat Washer
8 pcs.
F-I
8 pcs.
1 pc.
5mm Allen Wrench
F-J
Ø
5
16
x 12 x 3mm
Spring Washer
46170
4/6-5/0 UPH HEADBOARD
46174
4/6-5/0 PANEL HEADBOARD
46173 5/0 UPH BENCH STORAGE FOOTBOARD
46172 5/0-6/6 BED RAILS
Part A
Part B
Be sure to check all packing material carefully for small parts, which may
have come loose inside the carton during shipment.
To prevent possible
scratches or damage, this furniture should be assembled on a soft surface
such as a blanket or carpet.
To prevent possible damage to furniture and personal injury, it is
recommended that two people are used to assemble and set-up this bed.
Made in Viet Nam
Drawer Box
Support Leg
8-3/4" long with
leveler
F-H
F-K
M5/16" x 19*2mm
Flat Washer
2 pcs.
46173 5/0 UPH BENCH STORAGE FOOTBOARD
46172 5/0-6/6 BED RAILS
ASSEMBLY STEPS :
1. Place the Storage Footboard (F-A) face down on a clean and soft
surface.
2. Attach the Drawer Box Support Legs (F-E) using the Flat Washers
(F-I), Spring Washers (F-H) and 1-1/2" long Bolts (F-F). Tighten with
the Allen Wrench (F-K). See Detail A.
Detail: A
F-F
F-K
F-H
F-I
F-A
F-E
1 pc.
4mm Allen Wrench
R-G
R-G
Note: For a Storage Bed, the Wood
Slat Support Cleat mounted on the
back side of the Bed Rails must be
mounted at the upper location. If
needed, using the Allen Wrench
(R-G) remove the Bolts and
Washers and remount it at the
upper position on the Bed Rails. It
is mounted at the lower position
for a Standard Bed.
The Filler Rail mounted at the top
edge of the California King Bed
Rails must also be temporarily
removed to assemble the Slats on
the Bed.
Slat Support Cleat
