Riverbed 8000 Rack Installation Manual Download Page 14 | Manualshive

Page: 14 / 28

background image

14

Rack Installation Guide

Rack Installation Guide

Mounting Series 5050, 6050, 7050, and 9350 to a Rack

4.

Attach the first bracket to the chassis with the three included screws.

Figure 15. Attaching Two-Post Center-Mount Brackets

5.

Slide the second bracket onto the pegs of the first bracket by placing the second bracket over the first
bracket at the widest opening then slide towards the narrower part to secure.

Figure 16. Attaching Second Bracket to First Bracket

6.

Repeat steps 4 and 5 on the other side of the chassis.

7.

Center-mount the system on a two-post rack.

Mounting Series 5050, 6050, 7050, and 9350 to a Rack

The Series 5050, 6050, 7050, and 9350 ship with rails pre-installed to the chassis for mounting to a four-post
rack. The following section describes how to install a 5050, 6050, 7050, and 9350 system in a four-post rack.

«
...
12
13
14
15
16
...
»

Summary of Contents for 8000





























Reviews:

No comments

Related manuals for 8000

Brand: Panasonic Pages: 37

Brand: Panasonic Pages: 2

Brand: Yamaha Pages: 277

Brand: MORLEY PEDALS Pages: 1

Brand: Quooker Pages: 8

Brand: Hill Audio Pages: 21

Brand: Alto Pages: 35

Brand: Meyer Pages: 92

AC TrueTone 256818

Brand: Harley Benton Pages: 20

Let's Bake 31575

Brand: Lakeland Pages: 28

Brand: Pyle Pro Pages: 33

Brand: ADDAC System Pages: 17

Vibe Machine V-2

Brand: DryBell Pages: 18

Brand: Beko Pages: 100

Brand: Beko Pages: 112

Brand: Philips Pages: 25

MHC-GX555 - Mini Hi Fi Component System

Brand: Sony Pages: 44

TWINTONE Mark III

Brand: Koch Guitar Electronics Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands