RiTTO TWINBUS System Manual Download Page 47

Page: 47 / 197

Installation: Assembly, connection and start-up

tio

Concealed and cavity wall installation

A flush-mounted frame 1 7321 is required for installation. The flush-mounted frame is plastered in or attached using
the provided cavity wall clamps.

1. Cavity wall clamps
2. Fastening screws for cavity wall clamps
3. Plastering protection
h: 242 mm
b: 169.5 mm
t:

35 mm

Note:

The plaster protection (3) provides protection from soiling. It should only be removed

before the video indoor station is installed.

If the walls are not plastered, the thickness of the plaster to be applied must be taken into
consideration during installation.

00814-0

00815-0

00055-0

Summary of Contents for TWINBUS






































































































































































































Search results

Summary of Contents for TWINBUS

Reviews:

Related manuals for TWINBUS

Brands by name

Popular brands

RiTTO TWINBUS, System Manual

Search results

Summary of Contents for TWINBUS

Reviews:

Related manuals for TWINBUS

Brands by name

Popular brands