background image

24

 wwwritehitecom 

Publication:

 AMEN00119 2020-07-06

GLOBAL SALES AND SERVICE 

Representatives in All Major Cities

RITE-HITE WORLD HEADQUARTERS

8900 N Arbon Drive

PO Box 245020

Milwaukee, Wisconsin 53224

RITE-HITE CHINA

First Floor, Building #3,

558 Tongxie Road,  

Changning District

Shanghai 200335, China

RITE-HITE LATIN AMERICA

Alameda Lorena 800, conj 1310  

‑ Jardim Paulista

São Paulo‑SP, CEP 01424‑001  

‑ Brazil

RITE-HITE GMBH

Carl‑Zeiss‑Strasse 3

34471 Volkmarsen, Germany

 

414-355-2600

 

US Only:

 1-800-456-0600

 

+86-21-6237-6333

 

+55-11-3527-9590

 

+49-5693 98700

  LIMITED PRODUCT WARRANTY  

SlideAir

 Pneumatic Safety Curtain

Rite‑Hite Company, LLC and its affiliates (collectively "Rite‑Hite") warrant that the Product sold to the Owner will be 

free of defects in design, materials and workmanship (ordinary wear and tear excepted) for the periods set forth below  

("Limited Warranty")

One (1) Year(s) on all mechanical and electrical parts (non‑prorated)

One (1) Year(s) labor, based on Rite‑Hite approved travel and labor repair times

REMEDIES

Parts:

  Rite‑Hite's obligations under this Limited Warranty are limited to repairing or replacing, at Rite‑Hite's option, any 

part which is determined by Rite‑Hite to be defective during the applicable warranty period Such repair or replacement 

shall be Rite‑Hite's sole obligation and the Owner's exclusive remedy under this Limited Warranty

Labor:

  Rite‑Hite will provide warranty service without charge for labor per the specified warranty period Thereafter, a 

charge will apply to any repair or replacement under this Limited Warranty

CLAIMS

 Claims under this Limited Warranty must be made (i) within 30 (thirty) days after discovery and (ii) prior to 

expiration of the applicable warranty period Warranty period commences on the date of shipment Claims shall be made 

in writing or by contacting the representative from whom the Product was purchased directly Owner must allow Rite‑Hite 

or its agent, a reasonable opportunity to inspect any Product claimed to be defective and shall, at Rite‑Hite's option, either 

(x) grant Rite‑Hite or its agent access to Owner's premises for the purpose of repairing or replacing the Product or (y) 

return of the Product to the Rite‑Hite, FOB Rite‑Hite's factory

NOT WARRANTED 

Rite‑Hite does not warrant against and is not responsible for wear items such as fuses, batteries, 

bulbs, vision and seals No implied warranty shall be deemed to cover damages that result directly or indirectly from: (i) 

the unauthorized modification or repair of the Product, (ii) damage due to misuse, neglect, accident, failure to provide 

necessary maintenance, or normal wear and tear of the Product, (iii) failure to follow Rite‑Hite's instructions for installation, 

failure to operate the Product within the Product's rated capacities and/or specified design parameters, or failure to 

properly maintain the Product, (iv) use of the Product in a manner that is inconsistent with Rite‑Hite's guidelines or local 

building codes, (v) movement, settling, distortion, or collapse of the ground, or of improvements to which the Products are 

affixed, (vi) fire, flood, earthquake, elements of nature or acts of God, riots, civil disorder, war, or any other cause beyond 

the reasonable control of Rite‑Hite, (vii) improper handling, storage, abuse, or neglect of the Product by Owner or by any 

third party

DISCLAIMERS

  THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER REPRESENTATIONS 

AND WARRANTIES, EXPRESS OR IMPLIED, AND RITE‑HITE EXPRESSLY DISCLAIMS AND EXCLUDES 

ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR PURPOSE RITE‑HITE SHALL NOT 

BE SUBJECT TO ANY OTHER OBLIGATIONS OR LIABILITIES, WHETHER ARISING OUT OF BREACH OF 

CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORIES 

OF LAW, WITH RESPECT TO THE PRODUCTS SOLD OR SERVICES RENDERED BY RITE‑HITE, OR ANY 

UNDERTAKINGS, ACTS, OR OMISSIONS RELATING THERETO

LIMITATION OF LIABILITY

  IN NO EVENT SHALL RITE‑HITE BE RESPONSIBLE FOR, OR LIABLE TO ANYONE 

FOR, SPECIAL, INDIRECT, COLLATERAL, PUNITIVE, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF  

RITE‑HITE HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES Such excluded damages include, but 

are not limited to, personal injury, damage to property, loss of goodwill, loss of profits, loss of use, cost of cover with any 

substitute product, interruption of business, or other similar indirect financial loss

170714

Summary of Contents for SlideAir

























Reviews: