RITE-HITE SlideAir Installation/Service/Owner'S Manual Download

Page: 15 / 24

Rite‑Hite

Installation/Service/Owner's Manual

SlideAir™ Pneumatic Safety Curtain

Publication:

AMEN00119 2020-07-06

ELECTRICAL

Proximity Switch Wiring Diagram

BROWN

BLACK

BLUE

PNP

N/O CONTACT

THIS DOCUMENT IS THE PROPERTY OF RITE-HITE® DOORS INC. SUBJECT MATTER HEREIN IS CONFIDENTIAL. DO NOT USE, REPRODUCE, COPY OR DISCLOSE EXCEPT WITH WRITTEN CONSENT OF RITE-HITE® DOORS INC.

CONFIDENTIAL

M8x1 - 3 PIN

INDICATOR LIGHT

DETAIL A

PIN ALLOCATION

SCALE 6 : 1

PIN #1

PIN #4

PIN #3

NEXT ASSEMBLY

FINAL ASSEMBLY

5220M160

5220M162

REVISION HISTORY

REV.

DATE

NOTE

ECN

6/25/2019

RELEASE

7766

SHC

PIN ALLOCATION

PIN #

WIRE COLOR

ALLOCATION

BROWN

BLUE

BLACK

OUTPUT

SLDAIR

MODEL

06/17/2019

DRAWN DATE

SHC

DRAWN BY

6/17/2019

DATE ISSUED

FINISH

REFERENCE

72700322

PART#

.050

.010

.005

1.0

UNLESS OTHERWISE SPECIFIED

DIMENSIONS ARE IN INCHES.

TOLERANCES:

.X .XX .XXX ANGLE

7766

1 OF 1

2:1

5220M159

SW,PROX,FESTO,PNP,1370

RITE-HITE ® DOORS INC.

MATERIAL

DO NOT SCALE DRAWING

INITIAL ECN

ALL SHEETS ARE THE SAME

REVISION STATUS

THIRD ANGLE PROJECTION

DWG NO

SCALE

SIZE

TITLE

SHEET

REV

DOORS INC.

<5220M159

PDF>

Summary of Contents for SlideAir

























Search results

Summary of Contents for SlideAir

Reviews:

Related manuals for SlideAir

Brands by name

Popular brands

RITE-HITE SlideAir, Installation/Service/Owner'S Manual

Search results

Summary of Contents for SlideAir

Reviews:

Related manuals for SlideAir

Brands by name

Popular brands