manualshive.com logo in svg

Riso MZ1070, Technical Manual, Page: 122 / 150

Share
Download
Riso MZ1070 Technical Manual Download Page 122

[ 16-88 ]

MZ870 / MZ890 / MZ1070 / MZ1090

 (Revision 0.9)

PANEL MESSAGE

Error type

D01 [Print drum not installed]   (Drum No. 1)

Panel display

D01-*** 

Set Print Cylinder in Place

Error reset 

method

First print drum safety SW: ON, first print drum connection signal: ON, and first print drum lock sensor: ON 

<< Install the print drum to clear the error. >>

Error point

Error detecting condition

526

The print drum is removed. (The connection signal, safety SW, and lock sensor are OFF.)

527

The print drum connection signal is OFF after the print drum is installed.

528

The print drum safety switch is OFF after the print drum is installed.

529

The print drum lock sensor is OFF after the print drum is installed (time-out during insertion: 5 sec).

530

The print drum connection signal does not switch OFF within 5 seconds after the print drum safety switch 

switches OFF, when the print drum is removed.

581

The drum safety switch turned OFF during machine operation.

Error type

D02 [Print drum incompatibility]   (Drum No. 1)

Panel display

D02-*** 

Wrong-Type Print Cylinder 

Installed in Cylinder Position 1 

Replace with Correct Type

Error reset 

method

Replace with the correct print drum. (The print drum code must match the machine model.)

Error point

Error detecting condition

532

The print drum is incompatible.  (Drum code not correct)

580

The print drum is incompatible.  (Drum style not correct)

Error type

D03 [Ink cartridge not installed]   (Drum No. 1)

Panel display

D03-*** 

Install Ink Cartridge 

in Print Cylinder 1

Error reset 

method

First ink cartridge set SW: ON

Error point

Error detecting condition

533

The ink cartridge set switch is OFF.

Error type

D04 [Ink cartridge incompatibility]   (Drum No. 1)

Panel display

D04-*** 

Wrong-type Ink Cartridge Installed in 

Cylinder 1 or Cannot Read Ink Info 

Replace Ink Cartridge 

or Contact Dealer/Riso Office

Error reset 

method

Replace with a correct ink cartridge.

Error point

Error detecting condition

534

The ink cartridge is incompatible.

560

Error due to missing ink cartridge tag.

561

Ink tag communication error (tag communication error due to noise).

562

Abnormal ink tag information.

 

Checksum error, verification error, storage of master information, etc.

564

Serial number mismatch detected during the periodic ink tag serial number check.

575

Software error involving ink tag. 

Antenna CH selection error, erroneous writing of data to write-protected area.

5.  Set check errors (D**)

Summary of Contents for MZ1070























































































































































Reviews:

No comments