manualshive.com logo in svg

RioOutdoors 4S-WPH, Installation Instructions Manual, Page: 5 / 41

Share
Download
RioOutdoors 4S-WPH Installation Instructions Manual Download Page 5

5 | 

P a g e

 

 

1.3

 

CONTENTS OF KIT # 4S-WPH 

The contents of this kit are shown in the table, below. Before you begin your project, take an inventory of all items that you 

received from us. If any items are missing, contact us directly via email at 

[email protected]

. Include your name and 

shipping address and your order number, if available. We will respond within 24 hours with a resolution to your problem.  

Item SKU #, Description 

Item Qty 

Item Image 

4x4 Post Top/Floor 2-way Hex Elbow Bracket 

SKU# 4HL 

(The hardware required to mount each bracket are taped 

to each bracket)

 

3 

 

4x4 1-Way Elbow Bracket 

SKU# 4C1L 

(The hardware required to mount each bracket are taped 

to each bracket)

 

2 

 

4x4 Fixed Floor Anchor Bracket 

SKU# 4FA 

(The hardware required to mount each bracket are taped 

to each bracket) 

3 

 

4x4 Wall Mount/ Wall Post Hugger Bracket 

SKU #4WM 

(The hardware required to mount each bracket are taped 

to each bracket)

 

2 

 

Wall Anchor Bracket 

SKU #1WAB 

(The hardware required to mount each bracket are bulk 

packaged)

 

4 

 

¼ x 1-1/4” Lag Screw 

(This Qty shows the total of this item included in this kit)

 

76 

 

 

 

Summary of Contents for 4S-WPH










































Reviews:

No comments