Riken Keiki OX-591 Page 33 Operating Instructions Manual Download

Page: 33 / 36

(4) PW/TR light flashing

① System trouble 「Ｅ－００」
＜Cause and action＞

・Memory trouble inside of indicator/alarm unit.

Contact our nearest agent or RIKEN KEIKI.

② Sensor connection trouble 「Ｅ－０１」
＜Cause and action＞

・Non-connection of sensor, contact failure of connector and disconnection of sensor cable.
・Check “whether sensor is connected” or “the sensor cable connector is connected to the sensor.

If can not be recovered, contact our nearest agent or RIKEN KEIKI.

(5) Fuse disconnection

＜Performance＞

・This unit can not work.

＜Cause and action＞

・The trouble of this unit or trouble of external power source can be considered. Search this cause

and after taking its measures, replace the fuse with the designate one.

＊NOTE

The fuse rating for this unit is “250V/1A T”.

Summary of Contents for OX-591





































Search results

Summary of Contents for OX-591

Reviews:

Related manuals for OX-591

Brands by name

Popular brands

Riken Keiki OX-591, Operating Instructions Manual

Search results

Summary of Contents for OX-591

Reviews:

Related manuals for OX-591

Brands by name

Popular brands