manualshive.com logo in svg

Rigol MSO5000 Series, User Manual

Share
Download
Rigol MSO5000 Series User Manual Download Page 301

Chapter 18 Store and Load

 

 

RIGOL 

MSO5000 User's Guide

 

18-1 

Chapter 18

 

Store and Load 

 

You can save the current settings, waveforms, screen image, and parameters of the 

oscilloscope in internal memory or external storage device (such as USB storage 

device) in various formats and load the stored settings or waveforms when needed. 

You can also copy a new file of the specified type as well as delete and rename the 

specified type of file in the internal memory or external USB storage device via the 

disk management menu. 

 

Note:

 MSO5000 only supports the flash memory USB storage device of FAT32 

format. 

 

Contents in this chapter: 

 

Storage System 

 

Storage Type 

 

Load Type 

 

Internal Storage and Load 

 

External Storage and Load 

 

Disk Management 

 

Factory Settings 

 

 

 

 

 

 

 

 

 

 

 

 
 

 

 

 

 

 

 

 

 

 

 

 

 

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Summary of Contents for MSO5000 Series







































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands