Rigol MSO5000 Series User Manual Download Page 181

Page: 181 / 358

Chapter 6 Operations and Measurements

RIGOL

MSO5000 User's Guide

6-47

Track Measurement (before Horizontal Expansion):

Track Measurement (after Horizontal Expansion):

XY Mode

XY mode is only available when the horizontal time base mode is "XY" (refer to

"Timebase Mode"

). In this mode, two pairs of cursors will appear. You can adjust

the cursor positions to measure the X and Y values at the crossing points of the two

pairs of cursors.

Press

Mode

to select "XY" to enable the XY cursor measurement function. The

measurement results are displayed at the upper-left corner of the screen, as shown

in the following figure.



AX: indicates the X value at Cursor A.



AY: indicates the Y value at Cursor A.



BX: indicates the X value at Cursor B.



BY: indicates the Y value at Cursor B.

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Summary of Contents for MSO5000 Series







































































































































































































































































































































































Search results

Summary of Contents for MSO5000 Series

Reviews:

Brands by name

Popular brands

Rigol MSO5000 Series, User Manual

Search results

Summary of Contents for MSO5000 Series

Reviews:

Brands by name

Popular brands