manualshive.com logo in svg

Rigol MSO5000 Series, User Manual

Share
Download
Rigol MSO5000 Series User Manual Download Page 173

Chapter 6 Operations and Measurements

 

 

RIGOL

 

MSO5000 User's Guide

 

6-39 

 

 
Press 

Measure

 

 

Statistic

 to enter the sub-menu of "Statistic". 

 

Press 

Statistic

 to enable or disable the statistical function. 

 

Press 

Reset Stat.

 to clear the history statistics data and makes statistics again. 

 

Press 

Count

, then rotate the multifunction knob 

  or use the pop-up numeric 

keypad to set the count value. Its range is from 2 to 5000. By default, it is 1000. 

 
 

All Measurement 

All  measurement  could  measure  the  time  parameter,  count  value,  voltage 

parameters, and other parameters of the current measurement source and display 
the results on the screen. Press 

Measure

 

 

All Measure

 to select "OFF" (disabling 

the  all  measurement  function)  or  select  the  desired  channel  for  measurement 

(CH1-CH4). If  you  select "CH1", data of  all measurement  parameters of CH1  are 

displayed on the screen. 

Note: 

The  removal  operation  will  not  clear  the  measurement  results  of  the 

all-measurement function. 
 
 

Cursor Measurement 

 

Cursor measurement can measure the X-axis values (e.g Time) and Y-axis values 
(e.g. Voltage) of the selected waveform. Before making cursor measurement, 

connect the signal to the oscilloscope to acquire stable display. All the parameters 

supported by the 

"Auto Measurement"

 function can be measured with cursor 

measurement. The cursor measurement function provides the following two cursors. 

 

 

 

 

 

 

 

 

 

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Summary of Contents for MSO5000 Series







































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands