manualshive.com logo in svg

Rigol DS 5000C, User Manual, Page: 118 / 122

Share
Download
Rigol DS 5000C User Manual Download Page 118

RIGOL 

Appendix B: DS5000-Series Accessories 

Standard Accessories:

 

• 

Probe×2 (1.5m), 1:1, (10:1) Passive Probes 

The passive probes have a 6MHz bandwidth with a rating of 150V CAT II when 
the switch is in the 1X position, and a Full oscilloscope bandwidth with a rating 
of 300 V CAT II when the switch is in the 10X position. 

• 

Power Cable that fits the standard of destination country. 

• 

User Manual 

• 

User Registration Form 

 

Optional Accessories:   

• 

EM5-CM integration 

Communication module: RS232, GPIB, Pass/Fail output 

• 

EM5-COM communication module: RS232, GPIB 

• 

EM5-P/F Pass/Fail output module 

• 

UltraScope for WIN98/ 2000/XP software 

• 

Accessories case: PA-5000 

 

All accessories (standard and optional) are available by contacting your local RIGOL 
office. 

 

Copyright 2004 Rigol Electronic 

6-6

  User Manual for DS5000 Series

 

Summary of Contents for DS 5000C



























































































































Reviews:

No comments