Rigol DG900 Series Service Manual Download Page 24

RIGOL

 

Chapter 2 Troubleshooting&Maintenance

 

2-4

 

  DG900 Service Guide 

Care and Cleaning 

 

Care 

Do not store or leave the instrument where it may be exposed to direct sunlight for long periods of 

time. 

 

Cleaning 

Clean the instrument regularly according to its operating conditions. WARNING 

1.

 

Disconnect the instrument from all power sources. 

2.

 

Clean the external surfaces of the instrument with a soft cloth dampened with mild detergent or 

water. Avoid having any water or other objects into the chassis via the heat dissipation hole. When 

cleaning the LCD, take care to avoid scarifying it. 

 

 

CAUTION    

To avoid damage to the instrument, do not expose it to caustic liquids. 

 

 

WARNING

    

To avoid short-circuit resulting from moisture or personal injuries, ensure that the 

instrument is completely dry before connecting it to the power supply. 

 

 

 

 

Environmental Considerations 

 

The following symbol indicates that this product complies with the WEEE Directive 2002/96/EC. 

 

 

 

 

Product End-of-Life Handling 

The equipment may contain substances that could be harmful to the environment or human health. To 

avoid the release of such substances into the environment and avoid harm to human health, we 

recommend you to recycle this product appropriately to ensure that most materials are reused or 

recycled properly. Please contact your local authorities for disposal or recycling information. 

 

 

 

 

 

Summary of Contents for DG900 Series

























Reviews: