3
LEVEL
.
POST LEG
PAGE 1 OF 2
FASTEN WITH (2) WOOD SCREWS
LAY THE WORKSURFACE ON A PROTECTED SURFACE WITH THE
THAT WILL BUTT ANOTHER WORKSTATION. CENTER THE THE JOINER PLATE ON
5
THE EDGE OF THE WORKSURFACE 1/2" FROM THE FRONT AND BACK EDGES.
ATTACH (2) JOINER PLATES
CORDLESS DRILL
TAPE MEASURE
STEP 3:
8
HARDWARE PACK # 50643 & 50648
INTO THE PILOT HOLES ON THE WORKSURFACE. DO NOT OVER-TIGHTEN THE
ON EACH EDGE OF THE WORKSTATION(S)
SCREWS. USE A LOW TORQUE SETTING ON THE DRILL.
TO THE WORKSURFACE USING (3) OR (4) WOOD SCREWS
IN EACH JOINER PLATE.
2
5
. ATTACH THE TOP EDGE OF THE
MODESTY PANEL
WITH THE PILOT HOLES AT THE BACK CORNER OF THE WORKSUR-
TOOLS REQUIRED FOR ASSEMBLY:
INSTRUCTION # 50583
9
BEFORE BEGINNING
PILOT HOLES FACING UP. ALIGN THE HOLES IN THE PLATE AT THE TOP OF THE
INSTRUCTIONS
READ ALL THE
STEP 4:
5
FACE. ATTACH THE POST LEG WITH (4) WOOD SCREWS
VERSION DATED: 9/14/11
#2 PHILLIPS HEAD DRIVER BIT
R-STYLE™ WORKSTATION ASSEMBLY INSTRUCTIONS:
STEP 1:
LAY THE WORKSURFACE ON A PROTECTED SURFACE WITH THE
INSERTS AND PILOT HOLES FACING UP. ASSEMBLE THE RIGHT LEG ASSEMBLY
3
,
THE MODESTY PANEL
2
, AND THE LEFT LEG ASSEMBLY
1
USING (3) MACHINE
SCREWS
4
IN EACH LEG ASSEMBLY. DO NOT FULLY TIGHTEN THE SCREWS. IF
YOUR WORKSTATION HAS THE OPTIONAL WIRE MANAGEMENT CHANNEL,
INSTALL IT ACCORDING TO THE INSTRUCTIONS THAT CAME WITH THE CHANNEL.
STEP 2:
PLACE THE LEG AND MODESTY PANEL ASSEMBLY ON THE WORKSUR-
FACE
7
ALIGNING THE HOLES IN THE WORKSURFACE SUPPORTS WITH THE
INSERTS IN THE WORKSURFACE. ATTACH IT USING (2 OR 3) MACHINE SCREWS
6
ON EACH WORKSURFACE SUPPORT. FULLY TIGHTEN ALL THE FASTENERS
INCLUDING THE SCREWS HOLDING THE MODESTY PANEL
2
TO THE LEFT LEG
ASSEMBLY
1
AND THE RIGHT LEG ASSEMBLY
ITEM # PART #
DESCRIPTION
QTY.
1
VARIES R-STYLE™ LEFT LEG ASSEMBLY
VARIES
2
VARIES R-STYLE™ MODESTY PANEL
VARIES
3
VARIES R-STYLE™ RIGHT LEG ASSEMBLY
VARIES
4
R-STYLE A 6 x 15mm MACHINE SCREW
VARIES
5
51708
M5 x 18mm SQ/PH/WSHR HEAD WOOD SCREW
VARIES
6
50133
10-32 x 1/2 PHILLIPS TRUSS HEAD MACHINE SCREW VARIES
7
800512 2 X 2 WORKSURFACE JOINER PLATE
VARIES
8
29SL
29SL POST LEG
VARIES
6703 ZINSER ST., SCHOFIELD, WI 54476
PHONE: 800.298.4351 FAX: 866.882.9475
www.raproducts.com
K&A MANUFACTURING
5
5
WORKSTATION SIZES AND
CONFIGURATIONS WILL VARY.
ASSEMBLY STEPS ARE THE SAME.
STEPS 1-3
WORKSURFACE SUPPORT
3
1
2
4
6
7
LEFT & RIGHT R-STYLE™ WORKSTATION(S)
9
CORNER WORKSTATION
5
STEP 4
