DETAIL A
3
12
5
4
6703 ZINSER ST., SCHOFIELD, WI 54476
PHONE: 800.298.4351 FAX: 866.882.9475
www.raproducts.com
K&A MANUFACTURING
STEPS 1-4
2
1
WORKSURFACE
SUPPORT
A
PAGE 1 OF 3
VERSION DATED: 8/20/14
TOOLS REQUIRED FOR ASSEMBLY:
POWER DRIVER W/ADJUSTABLE
TORQUE
#2 PHILLIPS HEAD DRIVER BIT
#2 SQUARE HEAD DRIVER BIT
SMALL PHILLIPS SCREWDRIVER
3/16" HEX HEAD DRIVER BIT OR
ALLEN WRENCH
TAPE MEASURE
LEVEL
NewCrank SERIES 3.5 HEIGHT ADJUSTABLE WORKSTATION ASSEMBLY
INSTRUCTIONS:
STEP 1:
LAY THE WORKSURFACE
1
ON A PROTECTED SURFACE WITH THE
PILOT HOLES FACING UP. ALIGN THE HOLES IN THE WORKSURFACE SUPPORT
ON THE LEG ASSEMBLY WITH THE PILOT HOLES IN THE WORKSURFACE. NOTE
THAT THE CRANK CAN BE INSTALLED ON EITHER LEG ASSEMBLY.
STEP 2:
PLACE A CLAMP
4
ON THE CRANK HANDLE ASSEMBLY
3
. SLIDE THE
HANDLE ASSEMBLY INTO THE CRANK BRACKET
5
. PLACE THE OTHER CLAMP
ONTO THE HANDLE ASSEMBLY ON THE OPPOSITE SIDE OF THE CRANK HOLDER
FROM THE FIRST CLAMP. DO NOT TIGHTEN THE SCREWS IN THE CLAMPS.
STEP 3:
INSERT THE HANDLE/CLAMP/BRACKET ASSEMBLY INTO THE HEX DRIVE
NEAR THE TOP OF THE LEG ASSEMBLY
2
UNTIL IT BOTTOMS OUT. YOU MAY NEED
TO TURN THE CRANK HANDLE ASSEMBLY SLIGHTLY TO ALIGN IT WITH THE HEX
DRIVE. ATTACH THE CRANK BRACKET
5
TO THE WORKSURFACE
1
WITH (4)
WOOD SCREWS
1
2
. DO NOT USE ANY PILOT HOLES. DO NOT OVERTIGHTEN
THE SCREWS. USE A LOW TORQUE SETTING ON THE DRIVER. THE WORKSURFACE
MATERIAL COULD STRIP.
STEP 4:
SLIDE THE FORWARD CLAMP
4
AGAINST THE CRANK BRACKET
5
AND
TIGHTEN THE CLAMP SCREW. USE A SMALL PHILLIPS SCREWDRIVER. DO NOT
OVER-TIGHTEN THE SCREW. IT COULD STRIP. SLIDE THE CRANK HANDLE ASSEMBLY
OUT OF THE CLAMP BRACKET UNTIL IT JUST CLEARS THE FRONT OF THE WORK-
SURFACE. SLIDE THE BACK CLAMP AGAINST THE BACK OF THE CRANK BRACKET
AND TIGHTEN THE CLAMP SCREW.
INSTRUCTION # 53238
HARDWARE PACK # 53222 OR 53239
ITEM # PART #
DESCRIPTION
QTY
1
VARIES Series 3.5 Worksurface
1
2
VARIES NewCrank Series 3.5 Left Leg Assembly
1
3
VARIES NewCrank Series 3.5 Crank Handle Assembly
1
4
53141 NewCrank Clamp W/Screw
1
5
801315 Ketterer Crank Bracket
1
6
VARIES NewCrank Series 3.5 Hex Rod
1
7
VARIES NewCrank Series 3.5 Right Leg Assembly
1
8
VARIES Series 4 Cross Support
1
9
53025 5/16 Lock Washer
4
10
53024 5/16-18 x 1/2 Button Head Socket Screw
4
11
800934 Cross Support End Cap
2
12
51708 M5 x 18mm (7/8") Sq/Ph/Wshr Head Wood Screw 28
13
VARIES Series 4 LT 48" U-Channel
1
