Riello 20023353 Installation Instructions Manual Download Page 4

Page: 4 / 16

GENERAL INFORMATION

Identification

CODICE :

20025360

FABBRICATO IN ITALIA

DESCRIZIONE : CTE25V

S/N :

COLLETTORE SOLARE SOTTOVUOTO

DIMENSIONI: 1600X1730X145 mm

SUPERFICIE LORDA: 2,77 m

TEMPERATURA DI STAGNAZIONE: 268°C

SUPERFICIE DI APERTURA: 2,40 m

CONTENUTO LIQUIDO: 2,05 l

SUPERFICIE ASSORBITORE : 2,69 m

PESO A VUOTO: 52 kg

LIQUIDO TERMOVETTORE:

GLICOLE PREMIX (Acqua + Glicole, max concentrazione 50%)

FLUIDO NON GLICOLICO (Acqua + Inibitori di corrosione

at Potassio Formiato, max concentrazione 50%)

MAX PRESSIONE ESERCIZIO: 10 bar

da Riello S.p.A.

CEN 025

20022981_E4

EN 12975

10000001

BAR CODE 128B

Anno di produzione

SERIALE PROGRESSIVO

FABBRICATO IN ITALIA

DESCRIZIONE : CP25TVA

S/N :

COLLETTORE SOLARE PIANO

DIMENSIONI: 2046X1187X90 mm

SUPERFICIE LORDA: 2,43 m

TEMPERATURA DI STAGNAZIONE: 201 °C

SUPERFICIE DI APERTURA: 2,20 m

CONTENUTO LIQUIDO: 1,6 l

SUPERFICIE ASSORBITORE: 2,15 m

PESO A VUOTO: 36,5 kg

LIQUIDO TERMOVETTORE:

ACQUA+GLICOLE PROPILENICO

MAX CONCENTRAZIONE GLICOLE: 50%

MAX PRESSIONE ESERCIZIO: 10 bar

da Riello S.p.A.

20038498_E1

EN 12975

Certif. 011-7S1766 F

12000025

BAR CODE 128B

Anno di produzione

CODICE :

20038250

RIELLO S .p .A .

Via Ing. Pilade Riello, 7 - 37045 Legnago (VR) - ITALIA

Matricola

Modello

Codice

Data plate

Serial number plate

Code

Year of production

Serial Number

Description

by Riello S.p.A.

Made in Italy

Flat plate

solar collector

Dimensions

Gross area

Aperture area

Absorber area

Empty weight

Maximum operating pressure

Stagnation temperature

Liquid content

Max glycol concentration

Heat transfer fluid:

water+propylene glycol

If these plates or any other means of clearly identifying the product are defaced, removed or lost, proper installation and ser-

vicing may be rendered difficult.

IDENTIFICATION

Summary of Contents for 20023353

















Search results

Summary of Contents for 20023353

Reviews:

Brands by name

Popular brands

Riello 20023353, Installation Instructions Manual

Search results

Summary of Contents for 20023353

Reviews:

Brands by name

Popular brands