Rieber ACS 1600 O3 Digital Operating Instructions Manual Download Page 56

Page: 56 / 64

Cleaning, maintenance and care

Rieber GmbH & Co. KG

8.7.3

Note on cleaning the fan unit

Example: Left technical compartment

Radial fan

Diode of the plasma generator

➢

Unplug the mains plug of the radial fan/plasma generator assembly.

➢

Remove the assembly if necessary by sliding it along the guides, and place it on a soft surface.

➢

Eliminate any traces of grease. Then rub dry.

➢

WARNING

Leave the active carbon filter dry, keep away from moisture.

➢

Clean the soiled

surfaces of the radial fan

with a

hot cloth slightly dampened

with a

mild

detergent diluted in water. After cleaning, rub surfaces dry with a

soft cloth

➢

Install again in the reverse order.

8.7.4

Note on cleaning the plasma generator

At least every 3000 hours of operation:

Clean plasma generator

Failure to clean the

Diode

(2) on the plasma generator can cause unpleasant odours when using the

appliance, due to malfunction. See previous image.

➢

Pull the fan unit forward.

➢

Clean the diode on the plasma generator; For this, use a scratch-free cloth.
Use a little alcohol-based liquid if necessary, then rub dry.

Summary of Contents for ACS 1600 O3 Digital

































































Search results

Summary of Contents for ACS 1600 O3 Digital

Reviews:

Brands by name

Popular brands

Rieber ACS 1600 O3 Digital, Operating Instructions Manual

Search results

Summary of Contents for ACS 1600 O3 Digital

Reviews:

Brands by name

Popular brands