manualshive.com logo in svg

Ricoh SP 200SF, Operating Instructions And User Manual

Share
Download
Ricoh SP 200SF Operating Instructions And User Manual Download Page 55

Copying Both Sides of an ID Card onto One

Side of Paper

This section describes how to copy the front and back sides of an ID card or other small documents onto
either side of a sheet of paper.
When copying onto A4 paper, you can copy documents that are smaller than A5. Likewise, when
copying onto Letter size paper, you can copy documents that are smaller than Half Letter size.

• To use this function, the paper size used for printing copies must be set to A6, A5, A4, Half Letter,

or Letter.

CES165

Copying an ID Card

1.

Press the [

] key.

CTT101

On a Type 4 model, press the [

] key. If normal copier mode is being displayed,

press the [

] key again to switch to ID card copy mode, and then proceed to Step

3.

Copying Both Sides of an ID Card onto One Side of Paper

53

Summary of Contents for SP 200SF

































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands