Ricoh SP 200SF Operating Instructions And User Manual Download Page 105

Page: 105 / 192

Fax Features Settings

TX Settings

Immediate TX

Sets the machine to send a fax immediately when the original is scanned.
Default: [Off]

• Off

Select this when using Memory Transmission.

• On

Select this when using Immediate Transmission.

• Next Fax Only

Select this when using Immediate Transmission for the next transmission only.

Resolution

Specifies the resolution to use for scanning originals.
Default: [Standard]

• Standard

Select this when the original is a printed or typewritten document with normal-sized
characters.

• Detail

Select this when the original is a document with small print.

• Photo

Select this when the original contains images such as photographs or shaded drawings.

Density

Specifies the image density to use for scanning originals.
[Erase Background] is not available, when [Resolution] is set to [Photo].
Default: [Erase Background]

•

(Lightest)

•
•
•
•

(Darkest)

• Erase Background

Fax Features Settings

103

Summary of Contents for SP 200SF

































































































































































































Search results

Summary of Contents for SP 200SF

Reviews:

Brands by name

Popular brands

Ricoh SP 200SF, Operating Instructions And User Manual

Search results

Summary of Contents for SP 200SF

Reviews:

Brands by name

Popular brands